Most helpful. Just by reading this forum, I have learned much and have an idea of things to look out for to keep my rig out of the dealership.
Type: Posts; User: blueflash
Most helpful. Just by reading this forum, I have learned much and have an idea of things to look out for to keep my rig out of the dealership.
So I pulled the wheels off yesterday. Just wanted to look at the grease fittings. Found port and starboard brake lines had been rubbing on the inner fender well. Was able to loosen and reposition...
https://basscat.com/forum/groups/basscatowners/basscats-for-sale/ You can be on the lookout here also. Might want to check often. The boat market is hot right now seems.
^^^ This worked for me as well. I waited until i hit the water to allow for full range up/down. Thanks!
So what does a service contract cover?
Congrats! BassCat builds awesome boats.
I"mean not sure of all the details yet. This is it here: http://bowdenmarinesales.com/all-boats-for-sale/i/1996-ranger-461-vs-9f5d7d300d5b88f5f6c259411c3b2924
There's a 2016 Sabre single console a dealer has, with a 150 Opti with less than 200 hours. It has dual power poles and two 7" units. Supposed to be very clean. It's listed for $27,900. What would be...
I appreciate the ideas, guys. Fortunately, I get to fish often. Anything but a single axle is going to be a hassle.
I have to shove it to one side of the garage.
Found a 2006 18 Sabre for sale that I like, but it has a silver tandem axle trailer I can't use. Anybody with a good 18 Sabre single axle trailer would care to swap? I'm in Louisiana.
I see the 818 image has been added to the website. Anybody know the difference between the 618 and 818?
I see there is a 618 and 818 option on the Phoenix website?
Very nice. Is that trailer aluminum?
Oh I see looks like an option. I was getting ready to order one, will wait for more info on changes.
Anybody have any suggestions or similar past trouble?
My brother in law has his motor overheating with anything above idle in gear. Recently had the water pump replaced and I was told the old one had fallen apart. I checked the thermostat in a pot of...
Ballpark, older motors burn 10% ie 250 hp = 25 gph. Newer motors do better, but you have a loaded Ranger
SR2, what I did to test the TPS was key on , disconnect temperature sensor wires from port head. Next I took the meter and pierced the top TPS wire neg and the middle wire pos right where the wires...
Currently running a 4 blade 24 pitch brand unknown turning about 6400. I had Raker 24 pitch when the 150 hp Rude was on. The boat seems to like a lot of bow lift. Any suggestions?
I took a reading on 3 different spots on each head.
Hey guys. Dark side convert here after my Evinrude let go. I have a 1998 Mercury 175 EFI Ser # 0G752575 I just acquired. Was checking the heads with a temp gun and noticed the port side ran at 125º...
I got 900 hours out of her. Can't complain. I wanted to thank ChampioNman and others who have helped me thru the years keeping it running. :bows: :thumb up2:
Thanks hunt4deer, but I swapped them early on with the fuel pump and ignition relay. Turns out to be a bad power panel. I really appreciate the help, ChampioNman. The fishing is getting ready to...
Fellows I have a 2000 150 hp Evinrude model E150FPLSSV. Went to the launch the other day, motor started fine but trim would not operate. Figured it was the fickle connection at the power distribution...
The nut was very loose. (I torqued to 85' lbs per specs last time I had it off) What does the climate have to do with it cracking?