Search:

Type: Posts; User: Helo-md

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    27
    Views
    1,304

    Thank you so much! Gary

    Thank you so much!

    Gary
  2. Replies
    27
    Views
    1,304

    How about the wire bundle question?

    How about the wire bundle question?
  3. Replies
    11
    Views
    31,863

    After using a micrometer and a feeler gauge I'm...

    After using a micrometer and a feeler gauge I'm just a bit out so I adjusted as you posted! Thank you!
  4. Replies
    27
    Views
    1,304

    OK, 8.1 hours on the motor with no issues! I do...

    OK, 8.1 hours on the motor with no issues! I do have another question though, I pulled the cowling off to check things out for leaks and such and checked the idle and WOT position to make sure they...
  5. Replies
    27
    Views
    1,304

    Ok, New motor put back together! Need to pick...

    Ok, New motor put back together! Need to pick it up and break it in. All old pistons burned so new ones went in with all new parts. I do have a question that was raised to me. If the fuse for...
  6. Replies
    27
    Views
    1,304

    Ok, I just received the new block from Mercury...

    Ok, I just received the new block from Mercury racing (the box has the Mercury Racing sticker on it) and broke it out of it's foam cocoon. The cylinders are honed and look awesome! Will be driving...
  7. Replies
    27
    Views
    1,304

    They used all my inner parts except new Rods,...

    They used all my inner parts except new Rods, bolts, bearings and rings just put them in a new block. The pistons that came out of the old block were in excellent shape so they were reused.
  8. Replies
    27
    Views
    1,304

    These are the one the mech took to show me the un...

    These are the one the mech took to show me the un honed cylinders. I don't have pictures of the pistons out of the engine but will post after I deliver the new block.
  9. Replies
    27
    Views
    1,304

    So the block was sent back to Mercury and it was...

    So the block was sent back to Mercury and it was the newer block with a T72 at the end. Mercury is sending me a new block which before anything is done will make sure the sleeves are honed. Also I...
  10. Replies
    27
    Views
    1,304

    Sorry I didn't get back yesterday, Spoke to...

    Sorry I didn't get back yesterday, Spoke to Mercury Marine and was told that all blocks come off the line and shipped to the marine dealerships. They should be ready to assemble without the need to...
  11. Replies
    27
    Views
    1,304

    Mercury Block and end cap assy. 9811T68

    Mercury Block and end cap assy. 9811T68
  12. Replies
    27
    Views
    1,304

    According to Boats.net they are a authorized...

    According to Boats.net they are a authorized Mercury wholesaler. Don't know if that means anything. The Block is new not re manufactured and is a New Mercury product. The block was replaced because...
  13. Replies
    27
    Views
    1,304

    At first not getting power to the coil at all but...

    At first not getting power to the coil at all but after connecting to the smartcraft the spark decided to show back up. A complete diagnostic did not show any problems so the motor was started,...
  14. Replies
    27
    Views
    1,304

    2004 250xs lost spark on #1

    Serial # 0T819362
    2004 250xs

    Just had the engine built back up with new block and end cap. ran for 2.5 hours for the break in and motor shut off on me twice along with a low oil horn. Air bubble...
  15. Replies
    1
    Views
    170

    Hot foot cable for a Mercury 250xs

    I don't know if this is the right forum spot but I need a replacement cable for my mercury with a hot foot. dealership is pointing toward a Tele flex ccx630 but I don't want to buy one until I pull...
  16. Just using their repower to state they didn't...

    Just using their repower to state they didn't have a TACH problem. Have not done pressure checks yet, no partner to go with me available. Will do as soon as possible!
  17. OK, No Boom or Pop! Gained 200 rpm after...

    OK, No Boom or Pop! Gained 200 rpm after setting the plug gap and can now get to 5300-5400 but still acts like fuel starvation. I back down to 5000 RPM and it runs smooth. I didn't think there was...
  18. Don't have a choice on using the boat! Sponsors...

    Don't have a choice on using the boat! Sponsors paid for the event. But it has run good below 5000 so i'll keep it there just sucks having guys blow by me with 150's!!!!
  19. To answer a few of the questions, Since I have...

    To answer a few of the questions, Since I have had the re-power, the boat was very fast but never went above 5500-5600 RPM and I'm talking 76 MPH on the GPS and speedo. This was with a brand new 26p...
  20. 5100-5200 and then starts to surge

    5100-5200 and then starts to surge
  21. Just rebuilt the fuel pump, as questioned before,...

    Just rebuilt the fuel pump, as questioned before, would the plug gap cause this problem?
  22. Ok, pulled out all the stops and pulled...

    Ok, pulled out all the stops and pulled everything out that can be replaced. while checking the plugs I noticed that the mech didn't gap them, they were all set to .025! My merc book states they...
  23. Ok, all things have been replaced and cleaned...

    Ok, all things have been replaced and cleaned although I had no debris in the filter or chamber and fuel lines were intact. Was leary of taking the pulse pump apart but the directions were...
  24. removing the fuel tank cover/seat box on a TR-21

    Anyone know where all the screws are? I have found the 4 inside the storage and live wells.
  25. Replies
    128
    Views
    149,488

    Sticky: Jtomli, How many screws and what are the...

    Jtomli, How many screws and what are the locations to remove the cap on the fuel tank?

    Gary
Results 1 to 25 of 43
Page 1 of 2 1 2