Search:

Thanks for the reply. I really appreciate it.

Hello all,
This iis on port side in mid section of the block. Is this line in the block part of original casting ?
See the attached pick and share you thoughts please.
Thanks for any and all...

Good evening all, need some help.
looking at a vmax 150. Guy says it’s a reman unit about 4-5 yrs old.
Runs good, compression around 110 on all cylinders.
While looking over the motor I...

Got it. Thank you for the feedback. The pics look good to me but I didn’t
have anything to compare them to. Mostly fish less than 10’ in stained south Louisiana waters and trying to get the...

thank you for replying. would I gain anything with a G4

good evening all, i stalled a new to me helix g2. trying to get it dialed in. how do these pics look and do you think the install is good or can
be adjusted to be better. thanks for any...

Hello everyone
Can someone hempty me understand what these pics are telling me. Thanks for your help.
...

Hello all
im in search of a cover for a 999 or 959.
Please let me know if you have one

So the sharpness is designed to make the fish “pop” ?
not necessarily used to get a better picture on the screen.
great info. Thanks

So the sharpness is designed to make the fish “pop” ?
not necessarily used to get a better picture on the screen.
great info. Thanks

thanks for the feed back SLYDoggie and Wayne ! I went out for a couple hours today to get some more seat time. Heres what I got. Let me know what you guys think. I was playing with settings,...

Thanks for the insight.

Ok thank you. I know these are older units. Will it be a great difference on the mega units.
I might get one if they run deals for Black Friday.

Didn’t bring any rods. Forced myself to learn how to use and read
this darn thing.

evening everyone. I had to replace some units due to theft and was able to come across a set of 999's. at the console I was able to
install and try out the SI. Here are a few pics. I think i...

What motor height did you end up setting your motor ?
no matter if I go up or down my rpm and speed doesn’t change.
min stomped on this one

That’s my biggest issue. Nothing to compare
it to. Guys at skeeter says the tzx 200 hull
Wont go any faster and I should be content
with the numbers I’m getting.

I think I’m maxed out on this one. Got prop back and Ran today with cool air temps.
‘99 Johnson 225 HO3/4 tanks
myself at 220 lbs
total boat weight estimated 3025 lbs
3” best prop to pad (...

all the old info I can find on zx 200 skeeters are posted with 200 hp VMAX SHO 4.2 liter yamaha motors.
the performance bulletin shows at 5750 rpm top speed was 67.5 with a 25 pitch prop (15 1/8"...

With you vast knowledge, what is the real horsepower of the Johnny 225 HO ?

Thanks for response. I know you’re very knowledgeable
and I greatly appreciate your insight. How much of a difference
In a Johnny 1.86 gear ratio to Yammie 1.75 gear ratio when looking
at top...

Thanks for response. I know you’re very knowledgeable
and I greatly appreciate your insight. How much of a difference
In a Johnny 1.86 gear ratio to Yammie 1.75 gear ratio when looking
at top...

Thanks for reply. What’s your gear ratio ? My Johnny is
1.86. From what I can gather a lot of the yammies have
a 1.75 gear ratio. I’m told that makes a few mph difference.

new power pack and new stator installed. raised ptp and settled on the following:

Johnny 225 HO w/ carbs
1.86 gear ratio
Raker 26 (unworked )
2.5 below pad
5700-5800 RPM
69.5 gps top speed...

new power pack and new stator installed. raised ptp and settled on the following:

Johnny 225 HO w/ carbs
1.86 gear ratio
Raker 26 (unworked )
2.5 below pad
5700-5800 RPM
69.5 gps top speed...