when you're doing the google thing, be sure it has a ground connection also, otherwise, you will be running multiple grounds all the way to the battery. with a positive and negative connection on the...
Type: Posts; User: John Jones JTM
when you're doing the google thing, be sure it has a ground connection also, otherwise, you will be running multiple grounds all the way to the battery. with a positive and negative connection on the...
if its motorguide, replace both boot and switch. this is why its sold as a kit. as said above, minn kota does not use the boot.
on the second pic, looks to me like the bottom is the pressure line for brake fluid and has a light colored wire pinched, possibly the yellow we we keep talking about. the top cable is you're light...
the end of the cable can be fashioned with a pair of pliers to go through the barrel that holds the the cable on. after that, tighten the 2 set screws and you're done
your asc is correct. going to a brushless motor means at this time there is nothing available for repair work on this motor. motor would have to be replaced.
that pic is an Ultrex, and looks to be properly installed.
that will be fine
not sure what size you're needing, but this site may help.
https://www.waytekwire.com/products/?pSearch=marine%20tinned%20copper%20wire&psType=P&pageSize=36&pg=2
This is correct, just wires and appropriate fuse block is all that is needed
I had Jones Trollingmotor for 15yrs, during which time I rigged bunches of boats, even some straight from factory.
did you try to put stainless on stainless without using antiseize? if so, it aint coming off. time for a trip to an asc
with the kill switch on the shift plate, you're going to have to remove either the switch or the plate. you are correct that the kill switch goes to ground to kill the motor. on the switch, it...
the brake light and signal light are on the same circuit, fed by the yellow wire. the ground is usually common to all the lights. first disconnect ground any place it screws to trailer and wire brush...
that switch is different than most switches. when it connects, it disconnects the powerboard, so when it disconnects, the powerboard connects. take the switch out and squeeze the connections to make...
Heat the shaft and unscrew it from the motor. make sure the wires are loose up top so you dont twist them
went to basscat photos/specs and looks like it carries the width forward. now, if Basscat will let you choose consoles and get rid of the massive lid and the extension, yes, i know people are fishing...
Not sure on this charger, but on marine wiring, purple is usually hot with the key on. this tells me the key was turning something on in the charger. possibly some type of charge on the run system...
That setup would probably work, but as the commercial says, why go with just ok. i would do as mentioned above, but leave the bussbar alone. this would be 6ga from battery to console or inside...
Could be the grease inside the steering module getting thick. next time out in the cold, instead of just deploying and using, try turning it with the footpedal several times, i'm talking heal to toe...
You cant check deep cycles with a carbon pile load either. The load test ask for a lot of current on a short period of time like a cranking battery would give. deep cycles are designed to give less...
Is this going to carry the width forward like my 90 Caracal did.
This was a 90 Caracal I had:
440283440284
Malibu Red, silver bolt, black boot. several asked me it it held the heat, but it didnt.
John
has any chosen the Cougar with the hybrid Champion hull?
Lowrance is set up with files and folders. you can name a folder to a lake, up date the folder to the lake and store the folder. when that is done, looks like no waypoints in the unit. when you need...
depending how you are at measuring, you can get a custom made harness, right size wire, cut to your specs with the terminations needed. you will be charged for only the parts needed to build the...
JR19, its not just a Garmin. once transducers went to multi wire instead of coax, tape needed to be used instead of zip ties. a zip tie will crush the cable and damage the fine wires used in the...