How high were you running the boat when you slung a blade? I know this is a common issue. I have a 2022 ZXR20 and run the Atlas at 16 for max speed. Do I need to be running it lower? No, I...
Type: Posts; User: J5colli
How high were you running the boat when you slung a blade? I know this is a common issue. I have a 2022 ZXR20 and run the Atlas at 16 for max speed. Do I need to be running it lower? No, I...
Appreciate it.
My steering wheel has slight play in it front to back. If you grab the wheel with both hands, you can move it slightly front to back (by independently pushing and pulling from easy side). If...
It’s brand new quality line and I’ve had The rod guides and reel level winds checked. I don’t know what else to do.
I checked all of my reels and they really weren’t overfilled like everyone has mentioned. However, I did take extra line off of all of them just to make sure. I also tightened the spool tension,...
The issue arises even in open water. It’s with high resistance lures (chattrbaits, wide wobbling cranks, spinnerbaits, etc). I’ve been fishing for a long time with the same line and i haven’t had...
Thanks for the input guys; I do appreciate it. It’s not operator error and I take very good care of my stuff. I even tried replacing several tips by rod repair (manufacturer and local guy) just to...
If anyone else has suggestions or confirmation (on the above), please let me know. Thanks!
Appreciate it. I actually thought about that. I use Dobyns Champion and Falcon Cara rods and they both use Fuji guides. I’ll have to check on it to see if this is my problem.
Ok guys, I need some advice. I’m having issues with 5-8 different rods eating up my line. They eat up fluorocarbon in half a day or less of fishing. Mono will last a couple of trips and then...
Thanks for the info Wayne. I’ve restored the default settings and all that prior to the update and afterward. I just had a new shoot through installed last Friday. It’s doing the same thing as the...
Wayne,
I meant I’m having the same depth reading issue with it plugged in directly to the unit or plugged into the Y-Cable. It’s reading ok one minute and then reads 1.6ft. It’s been fine for...
Thanks Wayne. The transducers worked the same with the Y-Cable and plugged into the unit. SI works fine, but the 2D is having the same problem. Connections are good.
My original Y-Cable was a little corroded so I replaced it first since I had to get inside the boat to let slack out of the 2D transducer before bypassing the Y-Cable. The SI transducer performed...
I installed a new Y-Cable and had a new 2D transducer installed by a marine shop. Unfortunately, I’m still having the same issue. This started immediately after the software update. I updated on...
Thanks Wayne; I appreciate it.
What is the exact model number for the Y-Cable that goes to an 1198? Will the below model work? The duel ends on this model doesnt appear to be the same as what I currently have.
Humminbird...
Thanks guys. I did reset back to default settings, but it didn’t help. I’ll try the suggestions and let you know if I still can’t figure it out.
Appreciate it.
I did a software update last Friday night to the most current version – 7.67. I was on the lake Saturday morning and the sonar reading was going in and out at random. It would read correctly and...
I've loosened the mount and it doesn't appear to be the issue. In the stowed position, I can pull the rope and the pin and mechanism will stick and not release back to it's original position until I...
I'm using the factory pull Rope. The mechanism the pin is attached to is sticking (in the stowed position)and not releasing unless I actually move the mount up. Deploying and stowing is more...
I installed a new 112 Fortrex on my Skeeter and I'm having the issue with the pull rope unlocking it from stowed and deployed position. It's mainly pulling the rope from a stowed position. I can't...
I'm upgrading to a Fortrex 112 from an 80 Maxxum. After installing the mount, I noticed the back ourside corner of the mount doesn't sit 100% flush. I tried tightening the bolt back in that corner...
Appreciate the info John.
I appreciate the info.