Search:

Type: Posts; User: Simply_M

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    27
    Views
    918

    If the engine is tilted up you may lose fuel from...

    If the engine is tilted up you may lose fuel from the carburetors and have to reprime.
  2. Replies
    3
    Views
    268

    I have one on my pontoon and it shakes up to...

    I have one on my pontoon and it shakes up to around 1800 rpms.
  3. Try a different battery.

    Try a different battery.
  4. Replies
    2
    Views
    153

    Was hoping to find one cheaper. Thanks

    Was hoping to find one cheaper. Thanks
  5. Replies
    2
    Views
    153

    Johnnyrude easy timer

    Would like to know if anyone has one they would like to sell.
  6. I had a similar issue with one carb lean at idle....

    I had a similar issue with one carb lean at idle. The brass tube going down into the bowl was blocked. I was able to catch this by spraying fuel into the carbs individually and when I got to the...
  7. Thread: Prop Question

    by Simply_M
    Replies
    4
    Views
    179

    I use the same shooter on my 150 faststrike. Came...

    I use the same shooter on my 150 faststrike. Came on motor when I bought the boat, so I don’t have anything else to compare to.
  8. The hose just ran to the airbox would be an air...

    The hose just ran to the airbox would be an air leak causing the lean condition. Don’t know the correct layout though.
  9. Replies
    13
    Views
    679

    Reading through cdi electronics troubleshooting...

    Reading through cdi electronics troubleshooting tips, this sounds like a bad power coil.
  10. Replies
    13
    Views
    679

    Keeps running while the starter is engaged and...

    Keeps running while the starter is engaged and quits when the key is released to the on position?
  11. Replies
    30
    Views
    1,061

    I would suggest getting a plastic barrel large...

    I would suggest getting a plastic barrel large enough to put your lower half in with water. Muffs don’t replicate the back pressure you get from normal conditions in the water. This way you can...
  12. Replies
    3
    Views
    230

    Need to make sure the red lever on the primer you...

    Need to make sure the red lever on the primer you just replaced is in the correct position for normal operation. I think it should point down. If it’s in the correct position, then you need to try...
  13. Replies
    13
    Views
    679

    Could possibly be a bad power coil on the stator....

    Could possibly be a bad power coil on the stator. CDI electronics has some troubleshooting tips that explains how to check it out.
  14. I installed the uflex protech series on my 93...

    I installed the uflex protech series on my 93 faststrike. Uflex tech support were very helpful.
  15. Replies
    12
    Views
    543

    Don’t own one,but should he also consider...

    Don’t own one,but should he also consider availability of oil? Thought I have seen post about xd100 hard to find and expensive.
  16. Possibility of the primer not adding fuel when...

    Possibility of the primer not adding fuel when you try it. May have to remove the cowl and spray fuel into the intake to see if it is stumbling from being lean or rich. Does sound like heat soak....
  17. Replies
    10
    Views
    395

    I would try a different fuel tank or bottle of...

    I would try a different fuel tank or bottle of fuel directly to your primer bulb. Replace/inspect fuel lines. When it dies from fuel starvation, I would drain each carb bowl to see if they all lose...
  18. Replies
    10
    Views
    395

    I believe you have to unthread it and see if you...

    I believe you have to unthread it and see if you can blow and suck air through it. Could possibly thread in a barb fitting in place of the pulse limiter to test. Disconnect the pulse line from the...
  19. Replies
    10
    Views
    395

    Possibly the pulse limiter is bad. It threads...

    Possibly the pulse limiter is bad. It threads into the block and the fuel pump connects to it for the “pulse” to create the pumping action.
  20. Replies
    3
    Views
    213

    Some of the temp sensors are resistor type. Your...

    Some of the temp sensors are resistor type. Your engine needs the on/off type-normally open to ground. Newer sensor could be wrong type.
  21. Replies
    3
    Views
    213

    You could unplug the temp sensors to test. The...

    You could unplug the temp sensors to test. The temp sensor wires ran too close to the spark plug wires can cause weird things.
  22. Replies
    26
    Views
    772

    If it was running great until you replaced the...

    If it was running great until you replaced the starter,which required the removal of the flywheel, I would be rechecking that the flywheel is on the shaft in the proper position and timing.
  23. Replies
    10
    Views
    414

    Described as genuine oem bowl by seller. Came in...

    Described as genuine oem bowl by seller. Came in a generic plastic bag. Didn’t look like the genuine oem bowls I had got off amazon. Maybe not counterfeit,just lied to in the description.
  24. Replies
    10
    Views
    414

    Got some oem bowls on amazon. Some counterfeit...

    Got some oem bowls on amazon. Some counterfeit oem bowls on ebay. I think 4 genuine and 2 knock-offs. Need a rebuild kit for each carburetor also. I just shopped for whoever had the best price but...
  25. Replies
    10
    Views
    414

    I have the same motor and the bowls will warp...

    I have the same motor and the bowls will warp causing leaks. You can order everything easily and probably do the work yourself. Just do one at a time so that the intake manifold doesn’t break its...
Results 1 to 25 of 75
Page 1 of 3 1 2 3