I installed the Omega Dual Step with the Extra Step. Easy installation. I used stainless bolts instead of the (supplied) U-bolts.
Type: Posts; User: VinceR
I installed the Omega Dual Step with the Extra Step. Easy installation. I used stainless bolts instead of the (supplied) U-bolts.
https://scontent-ort2-2.xx.fbcdn.net/v/t1.0-9/122581619_10207649363629495_5198231098260801986_o.jpg?_nc_cat=111&ccb=2&_nc_sid=0be424&_nc_ohc=Tx2JDPEDuqsAX84lPil&_nc_ht=scontent-ort2-2.xx&oh=a70d51266f...
I will do that, thanks.
Thanks! Your setup is very similar to mine.
So, there should be no issue with interference between the two sensors? They will be about 18" apart.
Will I be able to mount the GPS Heading Sensor at the bow (the Compass sensor for the Ultrex is up front), or will it need to be mounted away from the bow?
I am getting ready to install an AS360TM (for Ultrex) on my boat. My setup is a an Ultrex, Humminbird 1159CI HD DI at the bow, and an 1159CI HD DI and 1199CI HD SI at the console (all networked via...
Mine is for sale in Michigan, but it is complete, boat motor and trailer. Still might be worth your while. I'm the original owner, bought new in 99': ...
Sorry about that. Try this: SPD-GS-5200-28. The SPD shocks are kind of hard to find, but the shock dimensions are 17" extended, 6" rod travel, 28lbs. of lift. West Marine has a replacement that is...
Miguel, if you have an Autozone, Advance Auto Parts, Murray's, Pep Boys or one of the major auto parts stores in your area, you should be able to find one there. Just take yours off, take it there...
Joe, see my response here (last post):
http://www.bbcboards.net...45469
I should add that the rivets that I used were 3/16" dia. by 3/4" long. Using back-up washers will help to keep them from...
I lost a bearing on mine about 6 years ago. It looked just about like that. I carefully filed down the surfaces where the bearing sits, then smoothed them out with emery cloth. I replaced the seal...
Joe, can you post a photo of the damage?
What part of the spindle is damaged? If it is the area where the seal rides, that may just be the stainless steel sleeve. Check it very closely. If it is the sleeve surface area that's damaged, the...
Be very careful when purchasing these seals from a source other than EZ Loader (Custom), or UFP. The OEM seals that are used are a special spring laoded, "double lipped" seal that prevents water from...
If you are taller than average, call Springfield direct, and order it. The stand-up pedestals that are sold at retail stores is 3" shorter than the OEM pedestal. I contacted Springfield to ask why I...
+3 Ditto. Especially for a box full of turbo charged smallmouths.
Did you check the NBAA website? They have four or five divisions in your neck of the woods. There are a couple of Weekend Challenge divisions, and a couple of Overtime (weeknight) Challenge divisions...
I'm fishing the NBAA Championship on the Ohio River, NBAA Overtime Challenge Division 28 (Lansing area), and the NBAA Saturday St. Clair Double Barrell Shootout. If money and time permit I'll fish...
I also found some gelcoat cracks on the cap of my 1999 201. They just showed up after 8 seasons of Lakes St. Clair and Erie. Mine were in the trolling motor area of the cap below the trolling motor,...
Way to go, Chad!
Represent Cobra owners AND Michigan.
http://www.bassboatcentral.com/boardstuff2/beers.gif
In my 99' 201, the screens on the drains in the livewell are removable. They are threaded onto the drains. I remove them from time to time to clean the screens, and flush the livewell drains.
If you have to change your aerator pump cartridges, do yourself (and your fish) a favor. Replace the factory installed 500 GPH pump cartridges with 750 GPH cartridges. The difference in the cost is...
I believe that the third hole (the one with no screen) is the livewell overflow drain.
Thanks, Larry. I've been a member since Al fired this site up, just haven't posted. I come here all the time to keep abreast of the goings-on at the plant. Like everyone else, hoping for a positive...