yam911,
Thanks for the info
Type: Posts; User: wcs69rat
yam911,
Thanks for the info
I have a question regarding whether or not the tilt trim sensor can affect oil injection. My buddy was at a local marina to pick up a new trim sender cam (clamp) today and the mechanic told him that...
Sorry to hear about your issues...I've been chasing similar problems with my 225 OX66. It appears that unplugging the rpm reduction switch on mine fixed my initial problem but the O2 sensor and plugs...
Probably the tilt / trim relay. I had the same issue on my OX66. If it's the relay, I would recommend going back with an OEM relay. I tried the cheap route and had two aftermarket ones last about two...
RL552,
As mentioned above, I unplugged the the RPM reduction switch that CJ1 suggested. The terrible vibration went away but it still had no power and would not get on plane. I found the O2...
Yam911,
Thanks for the diagram. I believe that the last time I checked the input voltage (red wire) it was right at 5 volts. I did not check it yesterday. I’ll try to do that this week sometime.
SELOC manual
I had not read the last two comments regarding the reeds when I installed them but I just installed a set of Chris Carson reeds and stuffer kit. The stock stainless ones appeared to be fine but I...
I was working some other issues on my motor and thought I would check the adjustment of the TPS voltage while I was at it. Mine was a little low; it was at .41 volts. My manual says to set it at...
CJ1,
Is the draft tube the same thing as the "dog bone" ? If so, it is clean and there is no build up at all on it.
Those plugs were fairly new and all had spark, however, I did install a brand new set the other day when I replaced the O2 sensor. I purchased the original set that had been in the motor for a couple...
RL552,
I haven't forgotten about updating you if I get my issue fixed. I disconnected the RPM reduction switch that CJ1 suggested and took it out to run it. It still would not get on plane and...
I ordered a new set of reed valves and a stuffer kit from Chris Carson Marine for my 225 OX66. My question is this: in stock form, there is a gasket beneath the reed block. When you install the...
Like 201PRO said...don't run Yamalube. It cokes up stuff like crazy. I have switched to Pennzoil XLF.
CJ1,
Will do. Thanks.
Drewtick,
Thanks, will do. I believe I spoke with you on the phone some months back, but my lead acids are almost new...I would like to swap over now, but may end up waiting a little while. I was...
I hope you guys don't mind me posting on the Phoenix forum; I'm usually hanging out on the Yamaha and Gambler forums. However, I was interested in this thread on Lithiums. Do any of you guys that...
RL552
Will do
The only light I have on the tach that is flashing is the temp sensor indication that has flashed ever since I installed that digital tach a couple of years ago. It seems to be independent of the...
I have a 2004 225 OX66. When I took the boat out a couple of days ago, it idled fine through a very long no wake zone. Then it was very sluggish getting on plane and top speed was way down. Top end...
Bellbass,
Thanks for the info. I managed to find it in an old thread. Sorry I just saw this message.
Thanks,
Found a guy on this forum with an OEM unit with very little time on it. Hopefully we can get the logistics worked out.
21XDC,
Thanks. I appreciate the info. Yourself as well as several others on this board always seem to help guys out with the knowledge you have. It is much appreciated.
21XDC,
Thanks for the info. Forgive my ignorance; what causes the loss in bow lift? Is it the lower gear ratio or does it have something to do with the shape of the lower unit?
Thank you.
I found the posting that I was originally looking for, but if anyone else has one, let me know. I may be interested. Thanks in advance.