800-900....
I’m talking hard to shift just stationary
Type: Posts; User: ggodwin
800-900....
I’m talking hard to shift just stationary
Does anyone know if these motors have any underlying problems in the shift mechanism? I have removed the cables and confirmed they are all fine. I was able to shift the unit by hand with the lower...
At the time, I had not started the motor so there was no evidence of anything.
Officially there was NOT a buzzer on this boat. No wonder he blew the HPDI. I used another set of controls and found a buzzer. I've got it all lined out for now. Still no trim working. It actually...
oh yea... my trim gauge is NOT working at the moment. No buzzers either. Unless the buzzer is behind the control box I think it’s been removed.
Thats good information to know.
i think this Ranger has the buzzer removed.
I can’t believe they’d design it that way. But, I’m sure they save some money with the same connector being used. I’ll check that out.
thank you!
Just checked and found a fuel pump wire unplugged. Got it plugged in now and the fuel pump is running.
now how about the alarms?
Well...
Not that you say it.
I got neither one.
I hear a "click". I have confirmed that the remote oil pump is filling up the reservoir.
But, I do not hear a fuel pump running. I don't get...
Just rebuilt an OX66 and installed it on a Ranger 520vx that had an HPDI on it. When I turn the key to on there is NO audible sound. I do hear a "clicking" but I do not hear a fuel pump or any...
Hey folks,
I am in the final stages of completing my rebuild on my 2003 OX66 200.
Currently I am planning these maintenance steps. Can you think of any others?
Replace the VST Filter,...
As you know the 2000 520vx has a built in setback however the motor is NOT adjustable.
What setback of an adjustable plate would you recommend being added to the 520vx? Is it possible to set it...
2000 520vx
Can someone tell me if the Ranger Aluminum wheels have a clear coat on them or are they just aliminum?
Also, does anyone know if the fiberglass wheel fenders are also gel-coat? Assuming...
Thanks for the information guys. I really appreciate the help.
Transom is solid
Ultrex 80#
Not sure what you mean about the lids being soft or cracked. To my knowledge they are just normal lids.
Help!
Any ideas what the value of a 2000 520vx with a blown HPDI is worth? Gel-Coat needs wet sanding and Carpet is 6.5 out of 10. Seats are new. I'm thinking maybe $10,500. Any suggestions?
I bought a 2004 OX66 200 hp with what I think is a low water pick up. Can anyone tell me how I can confirm what I have?
Seems like the given response by everyone is to call HydroTech.
I think JTM will use my own head. The HT kit will have the head and the matched head gasket. If I'm thinking clearly the heads are shaved but if the head gasket is not at the correct thickness then...
I've got a 2004 OX66 200 that I'm rebuilding and planning to have the heads shaved and reeds changed out. Has anyone used JTM Outboards insread of Hydrotech? Its about half the cost but not near the...
Does anyone know if the JTM Out Board shaved heads are as good as the Hydro-Tech heads? JTM is about half the cost.
On this one, I'm looking to buy it. I'm building an OX66 to go on it or another. boat I'm trying to come up with a a good offer that is fair. But also allow me to make some money when I sell it....
Thanks for your input. Very similar to mine. Are you considering the value of the blown motor?
Can you give me your opinions on the value of a 2004 ZX225 with a blown 225 HPDI? Good Condition.
I'm looking to buy this boat and install my OX66 on it.
Standard Equipment
Ultrex 80#
Garmin...
Just dropping this here. If there are any ZX225's or larger with a blown motor or motor removed I'd be interested in it. Looking for 2003 ish boat if possible. I've got a Yamaha OX66 to go on it.