Search:

Type: Posts; User: foot106

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    162
    Views
    3,063

    $1.89 in SC.

    $1.89 in SC.
  2. Replies
    162
    Views
    3,063

    1.89 in SC.

    1.89 in SC.
  3. Replies
    3
    Views
    151

    Thanks, I'll test and update back what I find.

    Thanks, I'll test and update back what I find.
  4. Replies
    3
    Views
    151

    Motor Guide 54 only has two speeds

    My motor guide 54 is only turning two speeds, seems like 2 and 3. Is this the speed selector dial or the motor?

    thanks in advance
  5. Replies
    14
    Views
    514

    Fill bilge with hose with plug in and see if leak...

    Fill bilge with hose with plug in and see if leak shows.
  6. Replies
    2
    Views
    257

    Look under the board sponsors or here Replacement...

    Look under the board sponsors or here Replacement & Reproduction Boat Logos from The Vinyl Approach.
  7. Replies
    289
    Views
    29,981

    howard4425@bellsouth.net

    howard4425@bellsouth.net
  8. Replies
    289
    Views
    29,981

    If possible I'd love a copy too. Thanks

    If possible I'd love a copy too. Thanks
  9. New fuel, clean the carbs, plugs, water pump and...

    New fuel, clean the carbs, plugs, water pump and change the gear oil.
  10. Replies
    1
    Views
    230

    Swap the wires on the relays and see if it it...

    Swap the wires on the relays and see if it it will go up but not down. Then you'll know which relay it is and that it is actually bad
    .
  11. Replies
    3
    Views
    204

    Mine did the same thing with the water flow...

    Mine did the same thing with the water flow sensors. I changed the bad one out, "Browns Point Marine". You can test them by unplugging the sensors 1 at a time. The motor will rev fine when the bad...
  12. Replies
    1
    Views
    175

    Outboard Marine Forged Pistons & Performance...

    Outboard Marine Forged Pistons & Performance Parts - Wiseco Piston Inc.
  13. Thread: oil leak ??

    by foot106
    Replies
    3
    Views
    334

    I have checked the lines and didn't find any...

    I have checked the lines and didn't find any leaks.How hard is that seal to change or do i need to drop off with mechanic?
  14. Thread: oil leak ??

    by foot106
    Replies
    3
    Views
    334

    oil leak ??

    I noticed 2 cycle oil on top of the engine on my 1987 150 ss.Am i correct in thinking head gasket since there is no oil lines on the top or rear of this motor?
  15. Replies
    1
    Views
    1,391

    Re: power Tilt/Trim oil reservoir refill help (XpressDawg)

    Any tilt fluid should work.Tilt all the way up and use a pump oil can to re-fill. You may need a helper to lift the motor up any you will probably have to use the emergency release valve.
  16. Thread: Trim motor

    by foot106
    Replies
    2
    Views
    239

    Re: Trim motor (foot106)

    OEM is about double the aftermarket in price.
  17. Thread: Trim motor

    by foot106
    Replies
    2
    Views
    239

    Trim motor

    My trim motor is on its last leg.(1987 150 ss) Which motor original suzuki or the aftermarket? http://www.bassboatcentral.com/smileys/eyes.gif
  18. Replies
    4
    Views
    706

    Re: 3 beeps question (foot106)

    Update.Water pressure is 20 lbs at WOT but about 5 at idle.This may be low since my gauge is tee'd into the tell tale stream and not the actual head.When first starting I have 0 lbs but builds after...
  19. Replies
    4
    Views
    706

    Re: 3 beeps question (foot106)

    I'm getting a flashing red light on the right side when idling.If I rev enging between beeps it runs fine. I changed both water flow sensors and one side is showng a constant red light so I unpluged...
  20. Replies
    4
    Views
    706

    3 beeps question

    When my motor is idling I'm getting 3 beeps. Is this water flow?It also cuts back if I try to take off while it is beeping but runs perfect otherwise.
    87 DT 150 SS

    thanks
  21. Thread: Any guidance

    by foot106
    Replies
    12
    Views
    913

    Re: Any guidance (foot106)

    UPDATE. I checked the idle mixture and had to reset every screw. Motor now runs like a champ. Had the carbs rebuilt but mechanic set mixture my ear and not by the service manual.Thanks to all for...
  22. Thread: Any guidance

    by foot106
    Replies
    12
    Views
    913

    Re: Any guidance (spego)

    I checked the idle mixture screws and set them at 1 3/4 turns. I think I'll try the 1 1/4 like the manual says next. I'm pretty sure its loading up because you can open the throttle wide open, it...
  23. Thread: Any guidance

    by foot106
    Replies
    12
    Views
    913

    Re: Any guidance (suzuki_man)

    Thanks, I'll try the 7's.
  24. Thread: Any guidance

    by foot106
    Replies
    12
    Views
    913

    Re: Any guidance (foot106)

    IT USES THE ngk B8-HS. What plug is hotter the 7 or the 9?
  25. Thread: Any guidance

    by foot106
    Replies
    12
    Views
    913

    Any guidance

    I have a 87 DT 150 ss that the first run of the day stinks. It will only come out of the hole if I start the engine and immediately punch it. Any idle time at all and it bogs down. The carbs have...
Results 1 to 25 of 31
Page 1 of 2 1 2