Search:

Hello, I'm Patrik from Sweden. Started my 250xs (0T998745) I just bought. Works fine on idle but when I throttle the engine it does not get back to idle speed and keeps the higher rpm despite all the...

Perfect, thx!

Hi,

I´m going to change from 15" to 20" mid-section and need to buy some new bearing and washers.

I do not find an exploded sketch for Mercury Racing 20 "offshore mid section online. Is it...

Hi, I have a problem that pops up on my Merc 200XS Gen 2 with the serial number 1E050867. It alarms for overheating at low speeds to mid, such as 0-60 mph or 0-4500 rpm, after this it is ok. Idle...

I have a 200xs Gen2 with the ser.no 1E050867. I use the Ngk IZFR7M, i can not find the right spec in the reccomenadations part about the spark plug gap, there is only info about the 300xs/IZFR7M. Do...

Hello, i am Patrik from Sweden. I have a 200xs Gen 2 with the serial number 1E050867 with 15 ". I've heard that you can replace the power trim piston so that you can tilt the engine all the way up....

Its a Exide Dual AGM EP 650 775A (EN)

The battery is brand new, its not one of the recommend but could my battery cause damage on the alternator?

I have also also moved the battery from the...

Hi, I have a 250XS 2005 with serial no 1E001254. Have to change the alternator three times this year. When the engine is off the SM shows 12.4 V and when its on it shows 11,4V. I took the alternators...

Sorry and Thx Don.

Serial no 1E001254

Patrik

Is the black hose with the white dot connected somewhere in the other end or is it only a draining hose?

It is a 250xs 2005

Regards Patrik

Is it possible to transfer the SC data information through a gateway to an IPad or Similar notebook? Patrik Serial No 1E001254

Don,
if the power heads are identical between XS and Pro XS, why recommend to two different oils when (DFI / Prem Plus) Patrik

Thx Don, I really appreciate your time you spend here for us who need your advices��

There is also more and more Mercury users here in Sweden who have start reading on BBC.

Patrik

Is it necessary to go for the "break in mode" after replacing the Air Compressor?

Also, there is three wires from the compressor. Two of them are males and the colours don't match the ones from...

Thx Don:thumb up2:

You got IM Mark. Thx

I have 250Xs 2005(1E001254) equipped with this LU. This LU has scoops, torque tab, no lower water intake in the torpedo and is unpainted from brand new exactly like my old SM. It is almost 5 Mph (85...

What is the difference on the flywheel between a 200XS and a 200 XS SST? Cheers Patrik

What exactly is the reason that the hose between the engine and the bulb will have a smaller diameter than the hose between the tank and bulb. The EPA hose kits that Mercury delivers together with...

Thx for info Don and sorry for OffTopic in the thread.

Is there more specs than the ECM who keeps the 2005 250xs faster than the other 250s? Or is just the ECM with increased rev limit?

Patrik

Don and others,
sorry if I gave the wrong explanation :embarassed:but this was what I had explained to me by the Seastar agent in Sweden. They claimed that when the cylinder not reach the bottom...

When i use to bleed the system I think it's important to loose the center ARP bolt to give the stearing possibility to reach each ends which is very often impossible with the bolt tighten on the arm...

Don, I did everything you suggested but without success.
One new thing that I noticed on the display was the warning "no starboard engine". Could that be a reason to my problems.

(Earlier my...

Thousands of thanks so far Don. I will try your recommended steps tonignt.