Search:

I just bought a few during Black Friday sales to try. I have not fished them yet. i bought them after listening to Tactical Bassin' video saying how well they fished though brush and lay downs...

For the the ones fishing the Megabass Vision 110 do you use the junior series. If so; only the winter time, or only on Spotted Bass lakes? Also; does the 110 jr. or the 110 jr. plus 1 work better for...

If ordering from them does not work out, let me know. I will sell mine at a good price, I'm not going to be needing both of the ones I have.

I have a spare one for a 2010 Z-7 that I think would be the same panel if are interested in buying one. I bought two before they quit making them.
This is new and never used.

I'm not an expert by any means on squarebill fishing. But; I bought the ALX Hustler this year after about a two year decision on where to buy this rod or not.
I had bought fiberglass rods in the...

I finally found a posting that someone had used ShutterFly.com and another that used Postimage.org with size 640x480.

I made my bow panel from King Starboard also. Was not cheap.
But; I also have an extra original bow panel, new in box, that I will sell.
The photos are of the one made from Starboard.


535792

I haven't posted photos in a while. I thought there was a sticky thread in "Help with Board Posting". But; I don't see it now.
I think the size was somewhere around 480x600 for a photo.
Any...

Thanks for all the replies, a lot of good advice I can use.
I decided I wanted to replace my bow panel because that's where I felt was the best place to put my new graph and I didn't like the...

I'm sure someone here has installed a second bilge pump or carries a secondary pump for emergencies.
If you have installed a second pump; did you tie the wiring into the first pump or run separate...

Thanks for the tips. I was looking at the J-B Weld Water Weld; but I will check out the Marine Tex Epoxy.
I don't want to go to larger screws knowing they will strip out later also.
I would love to...

Some of the screws that hold my bow panel in place are almost to the point of being striped. Stainless steel Sheetmetal screws.
Has anyone use something like the J.B. Weld Putty Epoxy to fill the...

The Cornfield ones look nice; but it looks as if they don't work on a standard post battery.
The ones from Drewcraft and Mercury I guess work by using a clamp-on post connector and then bolting the...

At the moment I use a single post add on connector; I think made by Ancor; and stack my wire connectors.
Plus use a nylon lock nut.
I bought the T H Marine 3 post multiplier; but not sure I like...

I have a Z-7. I put these on my trailer several months ago with good results. Sometimes I wish they were a bit brighter; but they definitely help.

I had a crack in my axle where the plate was welded for the brake. Replaced axle.
When welding a hairline crack like the one on your frame, I've was always told to drill a small hole at the end of...

Thanks for all the replies form everyone. I went back over everything, checking fuses to start with. Then reading diagrams and You Tube.
Finally I separated the truck and trailer and connected my...

Thanks for answering CatFan. I'll go back to the fuses. This truck has four fuse boxes, and at least two have fuses marked towing. I'll to figure out the one for the trailer backup lights.

Going through the manual of my truck (Toyota). In the section on towing; is Service Connector For Brake Controller for towing package.
Your vehicle is equipped with a service connecter for the...

Would that fuse be separate of the truck's backup lights?

The way I'm testing is for my wife to put the truck in reverse.
After writing my post, I have been thinking over my problem.
The lights I installed have tail, brake, turn, and backup all in the...

I have been wanting to put reverse lights on my trailer for sometime and did so this weekend. But they are not working.
I used the backup lights that 21XDC used from 4 State Trucks...

Thanks for all the replies. I'll try the easiest first.

I am looking at recoating (plus changing color) of some jig heads.
What is the best way to remove the weed guards without damaging the jig head if possible.
I know heat will work; but too much will...

I was asking about backup lights in Trailer Forum.
I had seen some that are mounted on top of the rear step that looked nice.
For you that have put backup lights on the tubular frames, how did you...