Search:

That's exactly the type of net I have and where I store it. I have a float on the retracted handle, just in case it blows out. I store it in the front center compartment until I start fishing and on...

I would not use a lithium cranking battery while the engine is still under warranty, at a minimum.

Motor sold!

Hoping to get some more hours on the motor soon. Finally through break-in. The 30p Bravo has run up to 87 in a short burst at full throttle but the plate can run higher than that run. There is...

I recently repowered my 2015 Allison BasSport Pro with a new V-8 and listed my old 2-stroke on the Motors page today. I bought it from Lee Sanderson and it has the Allison mods to the lower unit. It...

You can order a replacement latch directly from Eberhard. It's a Pull Ring Assembly ECL-130-KP8-MB.

I have a 2015 BasSport Pro Elite that had a 2015 250 Sport XS with 1.75 gears. I just repowered with a 2021 300R with 1.75 gears. I have 8" of setback (3" spacer & 5" CNC jackplate) with wedges. The...

I picked up a threaded bar, washer, & hex nut at Ace Hardware and put some Loc-tite on. Hope it holds together a bit better with the Loc-tite.

The bolt in my livewell plug rattled loose and the bolt and small washer must have flushed out before I realized what happened. Does anybody know who makes the plug that Allison uses in their...

I just did that same upgrade a few months ago and I used the transducer shield and saver bracket and shield that attach to the jackplate. I've been very happy with it.

Appreciate the offer, but I called Bill yesterday and ordered one.

Tim, I believe it is the Deluxe Sport steering wheel. It has the Allison logo with the number 1 in the center and has 3 double spokes that appear to be stainless steel or aluminium. It is a 2015...

Thanks, I'll check with them tomorrow. That is where I got the mounting bracket for my new HDS-9 Live.

I would like to create a little more room between my new graph and the steering wheel. Has anybody installed a spacer on their steering column for this purpose? Any suggestions? Thanks.

I will be repowering this summer and am going to sell my 2015 Mercury 250 Sport XS. It has the 1.75 gears and the Allison mods to the skeg and low water pickups. It has about 300 hours on it and...

The inside gap on the bracket that the motor toter is inserted into. Thank you!

If that is the case, that would make it easy. Would you be willing to measure the gap on your 300R to confirm the measurement? Thanks!

Dave Davis at DD26 indicated that the 300R gap is wider than the other engines. The DD26 website says that the standard size motor toters are not compatible with the 300R and Verado engines.

I am going to upgrade to a 300R 4 stroke and want to order a motor toter support for trailering. I was looking at the DD26 Fishing Mean Mount motor toter but the standard size does not fit the 300R 4...

I currently have 2.5" spacers, a 5.5" CMC jack plate, and wedges. Is this setback likely to perform well with the new motor and prop? Thanks!

I assume you would recommend a 30 M5 if I decided on a 300R. From what I have read about the M5 prop, I assume the hole shot would still be very good with the 30 M5 and the 300R.

Very interesting. My top end speed right now is 83.6, running a 28 Bravo 1 FS. It sounds like I would get an improved hole shot from the 4-stroke but should not expect any significant difference in...

I have a XB-21 BasSport Pro with twin power poles. I keep the boat loaded every trip. I have a 36V trolling motor and currently have 4 AGM batteries. I am repowering with a Mercury 250R 4 stroke with...

Merry Christmas!

I replaced my Marathons with Endurance and they have been great. No comparison to the old Chinese made Marathons.