Hydromotive Quad 4 28P. HydroTec Phase II 05 VMax 150 Carb. 70MPH GPS at 6200 RPM with a light load.
Type: Posts; User: hornytoad
Hydromotive Quad 4 28P. HydroTec Phase II 05 VMax 150 Carb. 70MPH GPS at 6200 RPM with a light load.
Brought my ZX190 in at 8:30 in the morning for a Phase II install and was out of there by 4:30 and on my way back to Mountain Home!
What about Pri-G gas treatment. Supposed to solve all your problems better than Stabil.
Phase II on my 150.
Welcome to the BBC Skeeter Board!!
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by skeeterbug25 »</TD></TR><TR><TD CLASS="quote">did the exhaust tuner make it sound...
Phase II on my '06 ZX190 was installed by HydroTec. Carbed 150 VMax will run 70 GPS with 1 person on board. No reliability problems but you must use 1 octane higher rated gas in the engine.
The 28P is not that radical. The vmax150 has 2:1 gearing if you compare that to the stock vmax 175 with the 1.86:1 and a 25m prop. Didn't notice much change in hole shot. With a full load o fuel and...
How many fish have you caught at 95 MPH?
http://www.bassboatcentral.com/smileys/stirthepot.gif
One thing for sure, they ain't being built in Mountain Home.
The pressure dyno uses a hydralic pump attached to the prop shaft as a load for the motor. I think the pressure on my motor stock was around 1200 psi and increased to around 1600 psi after the mod....
When they installed the Phase II kit on my VMax 150 carb, they ran the pressure dyno test both before and after the installation.
Lake Norfork is now 3 inches below the spillway breaking the high water record set in 1972. Heavy thunderstorms forecast for today and into Wednesday. Two generators running ful time in overload...
Gearing is different. 150 is 2:1 and I think the 175 is 1.86:1.
Hydrotech did all of the mods. Myself and Backlash Ar pulled the boat up to Nixa in the morning and it was finished by 4:30 the same day. It was run on the dyno both before and after the mods. Nathen...
Before the Phase II the boat would run about 59 mph gps with a med load and 1 person. This was with the stock Yami 23M prop at 5900 rpm. Since the mods I have used two different props, a 3 blade 27...
Just too set the record straight about the 2.6L carb motors -- My 06 ZX190 with the Phase II kit runs 68-70 with a 4 blade Hydromotive 28P prop turning 6,100 rpm. It was running 68 mph this summer at...
I am running a 150 carb on a ZX190. Ht phase II was installed last July and with HT driving hit 68+ on Tablerock. Prop was a Hydromotive 4 blade 28 pitch at 6100 rpm. Best run was last week on...
I am running a VMax 150 carb with the phase II kit on my ZX190. Before the mod, I was running 58 mph with a 23M prop at 5900 rpm. Now am running 68 mph in 85 degree water at 6100 rpm with a...
When you park your boat, open both seats and leave them open 'til they dry out.
I know you can do much better. Im running the same prop (blue printed and balanced) 28 pitch on a ZX190 with an HT 150 carb Yamie at 2" below pad. With one person and medium load and water temp 87 I...
Table Rock Lake, MO, Elev 950'
25 July 2007 - water temp 85 - air temp 79 - mild ripple low breeze
Boat: '06/ ZX190 DC
Motor: Yamaha VMax 150 carb, HydroTec Phase 2
Jackplate: 12" SlideMaster...
I am running the same setup as you are with a 23M on a 2005 150 VMax carb. The gearing is 2:1. RPM max is around 6000. Excellent hole shot and no chine walk. This is on a fully loaded boat (520lb...
There is a write up of sorts. Same data that you can get from Skeeter except according to the article, this boat has the new VMax 225 HDPI 2.6L small block Yamie with 2:1 gearing and a 14 1/2 x 25...
I added trailer brakes on my 2006 ZX190 single axle trailer. If you have a swing tongue it is somewhat more complex. There is gentleman in Mountain Home that does custom trailers and he installed my...