Looking for a good used 12” Lowrance Carbon. I would consider a 9” carbon but it wouldn’t be my ideal choice. If anyone is upgrading to Live, or another brand, and has a carbon to get rid of let me...
Type: Posts; User: O_D_O_T
Looking for a good used 12” Lowrance Carbon. I would consider a 9” carbon but it wouldn’t be my ideal choice. If anyone is upgrading to Live, or another brand, and has a carbon to get rid of let me...
No, this was the report I received. Would they be stored to where I could call and request the temperatures?
Back from the mechanic with a new water pump and diagnostic run. Boat had 135 hours when I purchased last July and now has 162 hours.
Code 38 at 114 hours Oil pressure pulses fault
Code 97 at 115...
Going to the boat Dr. on Monday. I’ll report back.
Would water pressure show warning signs of a water pump? I ran 4500 rpms last night and had 13 PSI. I looked for a chart but couldn’t find a water pressure chart for the 2012 and the numbers ranged...
Loser,
I replaced the filter and looked for air bubbles around the seal of the filter while priming and also when the motor was running. If there is another test I can do, please let me know.
...
Very informative, thank you!
To define my short runs, I typically bounce 1/2 mile to 1 mile increments (75% of the time). A long run would be 2-3 miles, with several idle spots within that distance. Would those short distance...
I’ll have to contact my mechanic, as I’m not certain. I hire that one out as annual maintenance to begin the season.
Yes, at the beginning of the season.
2012 Evinrude Etec HO
E150DHLINE
05329783
Motor fires right up, purrs like a kitten and runs strong with no spitting or sputtering. This is my 2nd season with her and no issues up until...
Thanks for the picture and measurement!
My setup would likely be a 24 volt system w/both batteries under the rod locker, no talons and no jackplate.
Maybe if no one knows for sure, someone could take a tape measure (or use their bump...
I’ve searched and asked several dealers but cannot get an exact answer.
When the trolling motor is down, how much higher out of the water are you standing in the Prov V Bass compared to a...
I’m located in Chatham and repair rods. ‘John RodandReel’ on Facebook.
Does the refurb shop repower?
Thanks for the replies guys, much appreciated. Nice video and that's exactly what I did. I originally ran screws in the live well lid but didn't like how it wouldn't remain open, which is why I went...
Rivets on my battery compartment and live well hinge on my 1998 R82 gave way (The battery compartment was a nice surprise as the pistol activated and shot the lid straight up in the air :laugh:).
...
I know you'll put it to good use! Nice to meet you and let me know how it performs.
Bump. Just going to throw it away if someone doesn't take it off my hands.
I have a white/gray Cabelas Signature Series (1" post) casting pedestal I need to get out of my garage. It has several stains but it's fully functional. It's in pretty good shape honestly. Probably...
Give Dan a call at D.C. Marine (815-671-3264). He's right there in Channahon and is one heck of a mechanic. No doubt in my mind he could get you rigged up.
I cut out a cardboard template and made sure the tray fit before actually cutting the deck. Some come with a template but those cost $130-$140, which was $40-$50 more than I paid for mine.
...
Anxious to try it out! Wasn't too bad to install, once I built up enough courage to start cutting . Next up is replacing cool hubs.
Installed a recessed trolling motor tray on the R82 Ranger thanks to BBC
http://imgur.com/imXZeQ9
http://imgur.com/pQcTqoO
http://imgur.com/eSUZXQJ
http://imgur.com/o8aZpGu