Search:

Type: Posts; User: Cobrafisher

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. I have the same problem. Does anyone know the...

    I have the same problem. Does anyone know the normal release method to release the front pedestal seat shaft on a 97' cobra 201d ?
  2. Replies
    2
    Views
    1,746

    Thanks!

    Thanks!
  3. Replies
    2
    Views
    1,746

    Cobra 201d seats

    Does anyone know where I can get a specific color bench seat for my boat, I can’t find matching white and maroon seats anywhere
  4. Thanks

    Thanks
  5. Help figuring out the livewells on my 97 201D cobra

    I tried everything to get them to drain but no luck, does anyone have a manual or diagram for my live well setup?
  6. Happy to say I got it running with no leaks...

    Happy to say I got it running with no leaks today. Used OMC gasket compound on both sides of the gaskets and on the bolt threads and NO LEAKS! I'm back to fishing!
  7. Replies
    7
    Views
    898

    I have a 97' cobra 201D travis edition..very very...

    I have a 97' cobra 201D travis edition..very very comfortable on the water, fishing and driving..as far as the transom I can lift up on the lower unit and the boat lifts with it, no flex or slack...
  8. Replies
    4
    Views
    253

    Did you find out what the problem was? I have...

    Did you find out what the problem was? I have almost the exact same problem after changing the head gaskets and water pump. Wondering if I crossed the temp wires coming from the power pack? Where is...
  9. thanks

    thanks
  10. 16956070-12je63hsm-1992-2001_johnson-evinrude-65-3...

    16956070-12je63hsm-1992-2001_johnson-evinrude-65-300-Hp_service_Manual

    Yes it was leaking prior to water pump installation but not nearly as much, I used johnson evinrude omc 345257 cylinder head...
  11. Also I didn't have any temp problems at all ever...

    Also I didn't have any temp problems at all ever before I changed the head gaskets
  12. New head gaskets leaking on 96' johnson 200 venom

    Changed out head gaskets last week and when I started it.. shortly after the temp light came on. I used the 15-17ft lbs torque suggested on this board.(My manual says 22ft lbs) Thought maybe I got...
  13. Haha..I'm sorry fella's. I didn't have the lower...

    Haha..I'm sorry fella's. I didn't have the lower unit fully tightened up flush so the hole in the linkage wasn't quite lining up with the pin end of the bolt . Went right in with the lower unit...
  14. 96' johnson 200 venom shift linkage bolt wont go back in after installing impeller

    Installed new impeller kit and everything went back together fine except the last little bolt, the one that screws into the linkage and connects the shift linkage from the lower unit. Came out fine...
  15. Just getting around to getting the heads back on...

    Just getting around to getting the heads back on in the morning..how long should the heat cycle be?
  16. 1992-2001 Johnson/Evinrude 65-300 HP service...

    1992-2001 Johnson/Evinrude 65-300 HP service manual......says...on 600 motors, apply a thin bead of rtv adhesive around each water passage on the cylinder block. On 90 degree motors, apply a light...
  17. Yeah I'm thinking they slapped it together once...

    Yeah I'm thinking they slapped it together once and were done with it.
  18. Also wondering which is considered the better...

    Also wondering which is considered the better option, with or without sealer?
  19. I cleaned the heads and they look new other than...

    I cleaned the heads and they look new other than being a little dirty..I've checked for warping and they don't need to be resurfaced. My main concern was about the sealer and whether or not leaking...
  20. Model is j200stledm

    Model is j200stledm
  21. Head gasket help on 96' johnson 200 venom

    I'm replacing the head gaskets on my motor and my service manual says to use sealer on "600 " motors and nothing on all others. What is the 600 designation? When I look online at head gaskets there...
  22. I pulled the heads today and they just fell loose...

    I pulled the heads today and they just fell loose when I got the bolts loose enough. Not sure if thats supposed to happen or not. It's very obvious the gaskets have been leaking and the piston in the...
  23. Replies
    3
    Views
    297

    Just wired in an all new harness and the lights...

    Just wired in an all new harness and the lights are working great!
  24. That's one of my next moves

    That's one of my next moves
  25. Yes it has been this way since I bought it about...

    Yes it has been this way since I bought it about a year and a half ago and I've been working on it here and there and trying to figure things out. The Raker prop is a 22..sorry. I'll check the...
Results 1 to 25 of 53
Page 1 of 3 1 2 3