I have a 250 pro xs ( 2b125142) and have been having problems with the shaft that holds the trim ram in coming out! I know this has been a known issue with the new 4 stroke pro xs models and was...
Type: Posts; User: masterbass
I have a 250 pro xs ( 2b125142) and have been having problems with the shaft that holds the trim ram in coming out! I know this has been a known issue with the new 4 stroke pro xs models and was...
Do i need the actual merc test harness to get an accurate reading on the tps? i did test it without the harness using my multimeter but it reads backwards! about 3.8v at closed throttle and 0.95 at...
Hey guys,
I have a 2001 225 efi (0T397411) it’s belongs to a good friend of mine and Im trying to help him figure out some issues! He came to me and said it wouldn’t idle on its own he had to give...
Ya I didn’t think so but thanks for confirming don. Was thinking on just buying a different gauge and running the sender to that gauge as a stand alone gauge and switching the smartcraft back to a...
Hey guys,
I have a a set of the sc1000 gauges in my boat with the additional system link fuel gauges and water psi gauge hooked up! I have 2 tanks in the boat and was wondering if there is anyway...
Thanks for the info don! I know I should have been more specific with a serial number but in this case I didn’t have a specific engine I was referring to.
I work for a marina and we are a yamaha...
When running the (oil pump prime) Feature on a m.e.d.s diagnostic software for optimax engines does it actually add extra oil into the cylinders and work as a substitute for winterizing instead of...
Hey guys,
I have a buddy with a 150 pro xs (2B399833) and he brought it to me having some issues at idle! Basically the engine will crank up and fire but won’t idle on its own unless you hold the...
Well I had her out this afternoon and got it to act up again but this time I had tools with me including my power probe circuit tester! Once I got it to act up I was able to start at the battery and...
Ya I checked for that and even pulled the back plastic cover off both sides of the connector to see if they were pushed out or looked damaged and I didn’t see a problem! Yesterday when I was in the...
I have a 16 pro xs 250 (2b125142) I’ve had some intermittent electrical issues that I can’t seem to nail down! Once in a while the motor wouldn’t start like a super dead battery! Basically you will...
Thanks don! Sorry didn’t have serial number just asking a general question on these motors as it seems all the ones I have come across did this! But you answered my question thanks again
It seems the new 4 stroke pro xs models have a trim limit switch built in. Once you reach a certain point when trimming the motor up it hits a limit switch and stops! Can this be shut off or does it...
try running the truck and spraying carb clean around the base of the intake to check for leaks! doubtful that's whats causing your particular problem but its worth a shot. Do you have access to a...
make it possible to scroll back on your side imaging like lowrance! should not have to pause screen to mark a waypoint! also make it possible to erase waypoints from any screen instead of having to...
Hey guys i have a 2016 250 pro xs serial number (2b125142) and today while out on the water my motor just shut off out of no where. Went to crank it back up and when you turn the key nothing happens...
Ok thank you guys for the replies. I will contact sea star and get a new one
I thought the same thing. Is that a mercury part or a sea star part?
http://www.bbcboards.net/attachment.php?attachmentid=283799&stc=1Hey guys,
i have a 2016 250 pro xs (2b125142)and been having issues with the adjustment coallr coming loose. I have adjusted it so...
I did take the compressor apart and its the rod bearing that went out. When i pulled it apart it was just because of the noise other than that rhe motor ran great. Im sure i still am going to have to...
So do i need tk find someone that does ultra sonic cleaning? I do not have time to send these out i need my boat back by friday
Thanks
Ok will do! Thanks for the input and help guys
Hey guys well today after fishing all day i was on my way back to the ramp and when i set down in a channel i noticed a squealing noise coming from the motor. It sounded like a bad bearing on a idler...
Well its obvious you guys are much better with computers than i am. I downloaded the humviwer and that didnt work. The humviwer page would come up but it said no file. When i load the sd card into my...
So just to add to the long list of problems i have had with my helix 12 units now i cant figure out how to view recordings from the unit on my computer. So i take a recording on my unit and pull the...