Search:

Type: Posts; User: kllr bee

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    68

    Check float real good. Richard aka Kllr Bee

    Check float real good.
    Richard aka Kllr Bee
  2. Replies
    14
    Views
    682

    I have a beede gauge that froze and worked but...

    I have a beede gauge that froze and worked but only went down to 15 pounds. I took it off and took the light bulb out and there was a brass ring I could see inside. I got a small screwdriver and put...
  3. Take the gauge out of boat. Take light bulb out...

    Take the gauge out of boat. Take light bulb out and you will see a copper ring inside put pressure on ring with small screwdriver and see which way needle moves, then bend til sets back to zero....
  4. Replies
    3
    Views
    108

    Ulterra 25volt deploy issue

    I have an older Ulterra that will start deploying and as it starts to tip down it will stop and start beeping. It will not continue but will retract. If you help it start moving by pushing a little...
  5. Replies
    8
    Views
    392

    Put a straightedge on your jackplate engine...

    Put a straightedge on your jackplate engine mounting surface extending down below boat. Measure distance from straight edge to bottom pad on boat. Mercury Racing recommends 1 inch of setback per...
  6. Thread: Whos Bullet?

    by kllr bee
    Replies
    9
    Views
    552

    Liquid sex!!! Richard aka Kllr Bee

    Liquid sex!!!
    Richard aka Kllr Bee
  7. Replies
    27
    Views
    1,081

    My 2006 21XD COMP had a tour 82. I fish mainly...

    My 2006 21XD COMP had a tour 82. I fish mainly single and got a minn kota Ulterra. You could not get me to give this baby back even if it cost me mph. I can launch alone and fish from anywhere in...
  8. I had a 2010 300XS. Ran it 13 years with nothing...

    I had a 2010 300XS. Ran it 13 years with nothing but Premium Plus per Mercury specs. Never turned a wrench on powerhead. Also most people on here know I will not hesitate to push one to the...
  9. Replies
    14
    Views
    347

    Always use Mercury parts on a high performance ...

    Always use Mercury parts on a high performance motor like this one. Some parts on this motor are not just 3 liter parts. Pay a little more now for piece of mind and fewer failures.
    Richard aka...
  10. Thread: TDR reeds

    by kllr bee
    Replies
    9
    Views
    463

    Boyesen 2 stage reeds........ I will put them...

    Boyesen 2 stage reeds........ I will put them against any reeds made. Better low rpm performance, mid range performance, and topend performance. Remember me?
    Richard aka Kllr Bee
  11. Thread: Tom Presley

    by kllr bee
    Replies
    15
    Views
    752

    My brother-in-law and all the other million plus...

    My brother-in-law and all the other million plus soles that died from covid would not call it political flu. Not funny!!!!!
    Richard aka Kllr Bee
  12. Replies
    12
    Views
    481

    If it will exceed 80 it needs a sport master. I...

    If it will exceed 80 it needs a sport master. I bet it would if set up right. On the sport master vs coned torquemaster, I ran 1.5 mph faster with Bob's coned torquemaster over factory sportmaster....
  13. Replies
    59
    Views
    2,646

    Howbout we put it this way, would a motor run...

    Howbout we put it this way, would a motor run better at sea-level or in say a mountain lake at 10,000 feet elevation? ��
    Richard aka Kllr Bee
  14. Replies
    59
    Views
    2,646

    Angleiron, If you're straw was pulling air...

    Angleiron, If you're straw was pulling air through a smaller straw it would be the volume that the smaller straw would handle. If a motor runs better with more air it means it is designed to...
  15. Replies
    127
    Views
    10,993

    #1 black spray paint matches perfectly with...

    #1 black spray paint matches perfectly with Mercury color.
    Richard aka Kllr Bee
  16. Replies
    59
    Views
    2,646

    I did see an article done by a guy with a...

    I did see an article done by a guy with a naturally aspirated 300R that said his motor picked up 5 to 6 mph. I know that when I was modifying EFI motors that raising the back of the cowl and adding...
  17. Replies
    59
    Views
    2,646

    Google Venom Vents and watch the video. Richard...

    Google Venom Vents and watch the video.
    Richard aka Kllr Bee
  18. Replies
    59
    Views
    2,646

    Sucks that Mercury would sell a 300 Race motor...

    Sucks that Mercury would sell a 300 Race motor and starve it by limiting air delivery to the motor. Taking all the fun out of fast bassin.
    Richard aka Kllr Bee
  19. Replies
    59
    Views
    2,646

    The computer is designed to take the air intake...

    The computer is designed to take the air intake and match with fuel output and be efficient. More air and more fuel makes more fun efficiently. Look the product up and watch the video. Those intakes...
  20. Replies
    59
    Views
    2,646

    Do you work for the EPA? I think increasing air...

    Do you work for the EPA? I think increasing air flow would help a motor run leaner and more fuel efficient than the stock configuration. Put that in your pipe and smoke it.
    Richard aka Kllr Bee
  21. Replies
    59
    Views
    2,646

    Would Venom Vents void Mercury warranty?

    Just watched video about Venom Vents and they make a big time difference on excelleration and top speed on a 450R that was tested on. Would adding Venom Vents void a Mercury warranty seeing that all...
  22. Replies
    127
    Views
    10,993

    JAZll,they could be performance addition...

    JAZll,they could be performance addition if.......
    Richard aka Kllr Bee
  23. Replies
    127
    Views
    10,993

    You know me. I'm always chasing extra juice!!...

    You know me. I'm always chasing extra juice!!
    Richard aka Kllr Bee
  24. Replies
    127
    Views
    10,993

    How much does a sat cost? I have an idea....

    How much does a sat cost? I have an idea.
    Richard aka Kllr Bee
  25. Thread: 21xrs setback

    by kllr bee
    Replies
    9
    Views
    393

    Best setback rule is 1 inch per foot of boat....

    Best setback rule is 1 inch per foot of boat. Straight edge on back of jackplate to bottom of hull.
    Richard aka Kllr Bee
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4