Search:

I am using 2 Battleborn 100 amp for a 24 volt motor. What I have found that both batteries will sometimes charge at different rates. One bank will turn green before the other has.
I have the...

Same problem with mine. Found a small crack in rubber return line from solenoid and replaced. All is well. 2000 year trailer.

You should figure out your power demands and what you are trying to power of the inverter. Then you can see if solar would be beneficial and cost effective for your needs. Alternator power is a whole...

You should be able to hear a clicking sound at solenoid if working.

This gauge from Balmar SG200 has recently came out on the market. Very accurate and also includes the ability for SOH which is an important factor in battery monitoring. Also the only one on the...

This may help.

https://goo.gl/images/bsBTTX

I agree with the AGM profile. Don't want it to go into auto Equalization which will do it in Lead acid profile. 13.2 should be around 70-80% charged.

I just bought a Minn Kota PC to charge my Battleborn lithium. Set the charge profile to AGM. My charger brought them to 14.4-14.6 and then when to float. I shut it off when it went to float. They are...

I recently purchased 2 Battle Born 100 amp hr batteries. I too was concerned with heat issues. I live in AZ where temps reach up to 120. Rare to be that hot but 115 is common during summer months....

Run a circuit protected cable to one of these?

https://www.waytekwire.com/item/47226/Power-Post-Red-3-8-160-Amp/

https://www.waytekwire.com/item/47202/Junction-Block-Stud-Red/

I want to follow up with the solution to my problem. First of all a short bit of info on what led to my problem.
(1) I wanted to install 2 new lithium trolling motor batteries.
(2) With new...

Do you see anything wrong with those pics?

What you said made a lot of sense. I got excited! Batt 1 neg went to black wire/prong. Batt 1 pos went to white wire/first side of jumper. Batt 2 neg went to other side of jumper. Batt 2 pos went to...

I have physically taken out and inspected jumper. No signs of any damage. Screws are all tight on plug. I have check voltage on across red and black and getting 12v. But I have not checked it with it...

Did that and getting 12v on both sides of the jumper. Not getting anything on red wire terminal. Sent and edit to my previous response. Maybe see if you see anything different.

I wish it was that. All breakers are functioning and not tripped. Could the plug be bad? I just don't see anything that could be bad. And I am getting voltage out of the prongs when plugged in, just...

Trolling motor is plug in. No arc. Before it was a direct short type arc. Not any more after the two suggestions you guys gave. Switched the grounds one more time and still no 24v reading. No arcing...

Yes that really helps. Thank you. No arcing. As I stated in the reply from CatFan I don't seem to get a 24 volt reading. Could it be the 12/24 volt switch on the pedal? This is the current wiring.

Thanks for your help. That seems to work. No arcing. I am now trying to figure out why the 12/24 switch is not going to 24 volts. With meter I am only getting 12 volts coming out of the back of the...

Do you mean just switch Battery 1 neg with Battery 2 negative? If I would move + and - diagonally I would be moving a positive lead to a "negative marked" terminal on the receptacle. Right now they...

2 12V lithiums. I will have to check that tomorrow. Thanks for your reply.

Attached is the pic of back of pug. Hopefully you can make out the jumper in the plug off of the white wire. And there is no jumpers on the batteries. Just the 4 cables running to the bow. 2...

#37Today, 12:41 PM

I am new to the forum and hope I can find some help in reqards to my problem. I have a 12/24 volt Motorguide 767 Brute. 2 batteries with 4 wires running to bow of boat with a 4...

I am new to the forum and hope I can find some help in reqards to my problem. I have a 12/24 volt Motorguide 760 Brute. 2 batteries with 4 wires running to trolling motor with a 4 prong receptacle...