Search:

Type: Posts; User: Pathornton

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    842

    So Don. Just to clarify. The shift position...

    So Don. Just to clarify. The shift position switch can cause a low oil and no oil light?
  2. Replies
    19
    Views
    842

    I’m sorry Don. I’m not bright. What is the shift...

    I’m sorry Don. I’m not bright. What is the shift switch and how do I check it?
  3. Replies
    19
    Views
    842

    We did it on boat side but if it’s supposed to be...

    We did it on boat side but if it’s supposed to be open a jumper is closing the circuit
  4. Replies
    19
    Views
    842

    Yes. I posted for him actually. When a jumper is...

    Yes. I posted for him actually. When a jumper is placed there it turns the low oil and no oil lights on in 30 seconds exactly and repeatedly, even if you just have the key in on position without...
  5. Replies
    19
    Views
    842

    Thanks. Yes I should have stated both tanks are...

    Thanks. Yes I should have stated both tanks are full. Doesn’t go without saying these days��
  6. Replies
    19
    Views
    842

    Sick optimax

    1998 225 opti. Sn 06725005. Runs fine for 300 yards. Throws low oil and no oil light. Goes into limp mode. Stays in limp 30 seconds. Lights go off, runs fine. And repeat over and over. Any ideas?...
  7. Replies
    5
    Views
    2,012

    Subscribed

    Subscribed
  8. Replies
    12
    Views
    815

    Sending it back tomorrow

    Sending it back tomorrow
  9. Replies
    12
    Views
    815

    2019 Phoenix 921. Two agm 31 series batteries...

    2019 Phoenix 921. Two agm 31 series batteries parallel. 6 guage ground from battery to buss bar in rod box. Dedicated 10 guagegeound from there to 360, and every unit and accessory. Shield wire...
  10. Replies
    12
    Views
    815

    Ok. So update. Checked everything I could think...

    Ok. So update. Checked everything I could think of with it installed so I removed it. Transducer cable and power wire are in a troll sock then run into under nose space in bow, then out to unit....
  11. Replies
    12
    Views
    815

    Not sure where the fuse is but I unplugged power...

    Not sure where the fuse is but I unplugged power wire just above shaft and checked pins with meter 12.46 volts
  12. Replies
    12
    Views
    815

    It is on a perko switch.

    It is on a perko switch.
  13. Replies
    12
    Views
    815

    Mega 360 wearing me out.

    Please help guys. Humminbird Helix 12 G3n si. Not networked. No y cable. Mega 360 plugged straight to unit. Worked fine for 8 months. Said mega 360 not detected a couple times. Unplugged 360 power...
  14. Replies
    9
    Views
    366

    Yes. The basemap downloaded to one depth finder....

    Yes. The basemap downloaded to one depth finder. Not to the other. In either case 2.28 should download first. It is not. It’s not recognizing that I even insert a card, other than locking up. Have to...
  15. Replies
    9
    Views
    366

    Yes to all. 8 gb card. actually has the same...

    Yes to all. 8 gb card. actually has the same 1.031 basemap download (unzipped) that i installed on my g3n yesterday. Only erased 2.28 for g3n si from card and replaced with 2.28 for g2n si. Thanks
  16. Replies
    9
    Views
    366

    Ok. I’ll try again. Removed and reinserted 6 or 8...

    Ok. I’ll try again. Removed and reinserted 6 or 8 times. Got no response from unit ����*♂️ Thank you
  17. Replies
    9
    Views
    366

    Another software question

    I have a Helix 12 si gn2 and a 12 di gn2. 2.28 is available for them. Downloaded si version to sd card and put in unit and it does nothing. Currently has version 1.640. Too big of a jump? Options?
  18. Replies
    2
    Views
    218

    Thank you sir

    Thank you sir
  19. Replies
    2
    Views
    218

    Software update

    I accidentally spent 2 hours downloading 1.031 basemap and 2.280 for a G3n si helix 12. I have a G3n di helix 12. Question. Can I simply replace the 2.280 with the di version? Is the basemap download...
  20. Replies
    13
    Views
    1,366

    thanks

    thanks
  21. Replies
    13
    Views
    1,366

    thanks

    thanks
  22. Replies
    13
    Views
    1,366

    Anyone found the source of this? I loosened the...

    Anyone found the source of this? I loosened the front of the chaps and got the bolt out of mine. 1/4 inch flanged bolt, 1 and 3/16 inches long, 10 mm head, F stamped on head, stainless. Anyone know...
  23. Replies
    16
    Views
    476

    Thanks guys

    Thanks guys
  24. Replies
    16
    Views
    476

    I don’t doubt that it would be ok. Guy just...

    I don’t doubt that it would be ok. Guy just said.that he’d had one lock up 2 weeks ago. Better safe than sorry I guess. Thanks
  25. Replies
    16
    Views
    476

    Actually since I’ve asked on here ive been told...

    Actually since I’ve asked on here ive been told the same thing by an authorized seller/installer and by a guy who does seminars for Humminbird. They didn’t say it WOULD, they said they sometimes do,...
Results 1 to 25 of 408
Page 1 of 17 1 2 3 4