This Bill, appreciate the info.. Plate reads 150, I'd love to put a 175 on it..
J
Type: Posts; User: jaytd
This Bill, appreciate the info.. Plate reads 150, I'd love to put a 175 on it..
J
I'm following this thread as I'm in need of a re-power and my dealer has recommended the Suziki 150 SS. is there any difference between the 2020 model and 2021 model, I see post about the new lower...
Thank you BT.. update complete, hope to test on the water tomorrow.
J
Thanks Wayne.. update completed successfully to 2.180, hope for a "on water" test tomorrow but self test shows everything connected back up.
One question if I may, the Transducer installed is...
GM All.. Long overdue but time to update software on above unit currently on Software version 1.54. In addition to the Helix 10 with XTM9 MDI T , I have Ultrex, 5 port Ethernet switch and 1199...
Hello Wayne.. Long Overdue but time to update software on my Helix 10 Mega DI G2N. Current SW version is 1.54, I have an Ultrex, XTM 9 MDI T transducer, 5 port ethernet switch and 1199 Networked. ...
I know we haven't seen the new or next Gen release of Solix, but do the current Solix units have the same issue with Depth Jump as the Helix Mega?
Thx
J
I've had my new Helix 10 Mega DI installed for a couple months now, when I first put it in I had good DI images, but recently my DI seemingly is not working, I get no viewable image from DI. I...
I wanted to send a positive follow up on this. I sent my 1199 in to HB repair fully expecting to pay the $410 repair charge to fix the reboot issue I was having. Turn around happened inside 5 days...
Well.... thanks Wayne for the help and getting me to my decision point quickly. On a side note, the Helix is working great. I self installed it and the Ultrex and have not experienced any of the...
Move cables, Duhh.. Moved units much easier. Unfortunately, Helix started on 1199 power but 1199 had same restart problem on Helix power...
J
Separate and Isolate,, good idea. Will take some cable pulling and manipulation, will let you know what I find.
Thx again
J
Thanks Wayne..
Removed the Card, no change. I disconnected the Ethernet cable at the switch , figured it didn't make a difference which end but let me know if I should remove it from the HB. ...
My 1199 is having a problem, on startup it begins the load, gets to the "press exit to continue" screen, I push exit, the screen comes up for about 2 seconds and then flashes up "shutting down "...
Thanks everyone for the response and ideas with this. I'm going to rewire the plug one last time, if I still have problems I'll eliminate one way or another.
Can I ask where you get the stainless...
Thanks all that have replied on this thread. I removed the plate on bow that has the Female side of the TM plug, cleaned the terminals and verified I have 24V at the front. I plugged the TM back...
Thanks blkfalc4.. I've run the MAXX 29C's for years and never had problems. Do you have I-Pilot Link on your Ultrex? I can't imagine that could add much draw, but at this point I have to...
Thank you for the quick reply
Wallmart Everstart MAXX Premium. 29DC. The Ultrex was self installed, but from a wiring perspective I used the original Stratus manufacturing wiring from the old...
GM all.
Been on the water twice now with New 24v 80 Lb Ultrex with I-Pilot Link and both times getting 3- 4 hours before Ultrex stops working, seemingly no power ( indicators all dark), foot pedal...
Thx Wayne.. Rainy day project can continue !
J
Does the Helix 10 have the same power connector as a HB 898? Just started my Helix 10 install and found it was shipped without the 6 ft power cable connector. I plugged the 898 cable into the back...
As always, thanks Wayne..
I finally pulled the trigger, new Ultrex and Helix 10 all self installed ( in progress ). Could not imagine doing it without BBC and the wealth of knowledge and...
What is the correct Part Number for the 5 Port Ethernet Switch that will link Helix 10 Mega Di G2N , 1199Ci HD Si and Ultrex with I-Pilot Link? Reason I ask, I just came from Cabellas and they had...
Hello all..
I just purchased and installed a new Ultrex with I-Pilot Link. I have a 1199 at the Console and intend to add a new Helix 10 Di Mega at the Bow ( replacing 898). With those 3 units...
Thanks Guys, appreciate the info. I just installed the Ultrex with I-Pilot Link and intend to test run it without connection to anything while I make decision on new Helix unit purchase to replace...