If you go on the Ranger website and select the model that you are interested in, and then choose “build your own”, part of the build tool lets you select custom colors. So you can see the exact boat...
Type: Posts; User: Dkrum
If you go on the Ranger website and select the model that you are interested in, and then choose “build your own”, part of the build tool lets you select custom colors. So you can see the exact boat...
Thanks Don!
2017 L4 Verado, 200 HP, Serial # 2B453183 Model # 1201V23ED
Prop is a 19" Pitch stainless Tempest Plus
Which is the best hub for this combo? Flo-Torque 2, Flo-Torque 4 or Flo-Torque SSR? Or...
Thanks for the help!
Well today everything worked perfectly! So maybe switching the ports around and then doing a couple of reboots did the trick! I will confirm software versions and IP addresses.
Everything is brand new. I did move ports around to get this far. I think the two Helix units have the latest software. I can try restoring the factory defaults next.
I have a new setup in my boat, helix 10 G4n SI at the console, helix 10 G4n DI at the bow, 24 volt terrova with iPilot link, all connected through a 5 port hub. The bow unit doesn’t see the SI, I get...
Thanks, I’ll give that a try!
489193
Here is a picture of my gauge, thanks!
2013 Merc 150XL Four stroke, Model # 1150F23HD Serial # 2B049721
My tilt trim gauge barely registers until the motor is well into the tilt range. Is there any adjustment or calibration that I can...
I got it out, thanks. Turns out that there were two screws buried deep in the carpet.
Does anyone know how to remove this panel on the front deck of a Ranger 186 Reata? If there are any other screws, they are buried so deeply in the carpet that I can’t find them!
Yes, I do have vault hubs. I checked the inner grease seal on the back side and they look good. They don’t seem to be leaking grease, but I have 5 years on them so I’m wondering if they are due for...
I have the same boat only with an I4 200 hp Verado. Trimmed out and running for best fuel economy, I get about 3.4-3.6 mpg with typical loads. So, I think 1.5 mpg seems low. What is your top speed?...
I have a 2017 Ranger 1880MS on a single axle trailer. I think that it is about due for maintenance on the trailer wheel bearings. What am I looking for to determine if I need to replace the wheel...
Congrats - Let’s see a photo!
plor25 - Your post says that your transducer is fitted "in hull". Are you saying that you have a shoot through hull transducer epoxied in down in the bottom of your bilge? Or is it on the transom on...
Data - That is exactly what I did. today I was out on the lake and I have DI, SI and 2D when I am moving slowly. Once I get over about 6 mph I loose 2D. So I think Wayne P is right, the transom...
Noid - Yes, I do sometimes turn the unit on before I launch the boat. Is that harmful? What about the sonar on the trolling motor when I stow it and go from spot to spot? I don't turn the sonar off...
No, I checked that. Good idea though.
The sonar (2d, DI and SI) on my Helix 10 Mega SI G2N has stopped working. GPS, network and all other functions still work normally. My setup includes a Helix 9 at the bow, Ulterra with iPilot Link,...
I tied/taped a chord and to the head unit end of the old cable and pulled it through. That worked well. Thanks for the tip!
The transducer on my Humminbird Helix 10 Mega SI G2N has failed. I have ordered and received a replacement transducer. Any tips/tricks to installation and pulling the cable up to the head unit in a...
Most likely the switches are bad. I have an 1880 MS and had the same problem with the indicator lights on many of the switches. Ranger sent new ones under warranty.
Thanks for your reply Wayne! I will look at it the next time that I'm on the boat!