Search:

Type: Posts; User: AHens

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    407

    Year and model of boat helps. Judging by the...

    Year and model of boat helps. Judging by the wheel, looks like Y2k ish. Probably oil bath.
  2. Replies
    13
    Views
    1,050

    This. As easy as it gets.

    This. As easy as it gets.
  3. Replies
    9
    Views
    977

    Spray soapy water to find the problem. Could be a...

    Spray soapy water to find the problem. Could be a leaky valve stem. Cheap fix if you only pull 2 miles. Just saying.
  4. Replies
    6
    Views
    329

    One gauge, two sensors. One for each tank.

    One gauge, two sensors. One for each tank.
  5. Thread: Hubs

    by AHens
    Replies
    5
    Views
    430

    Hand pack the bearings and change the cap to...

    Hand pack the bearings and change the cap to either a regular grease cap or bearing buddy cap. new rear seal. All parts will be the same except cap. Size should be 2.33 cap
  6. Replies
    9
    Views
    1,056

    Always replace both sides at the same time. If...

    Always replace both sides at the same time. If your not the original owner, one side may have been replaced. Be sure to change all associated nuts and bolts so you know what what you have. $.02
  7. Thread: Ranger trail

    by AHens
    Replies
    10
    Views
    921

    A-70 or XR-84 is the self latching.

    A-70 or XR-84 is the self latching.
  8. Replies
    4
    Views
    379

    Check a local (any brand) boat dealer?

    Check a local (any brand) boat dealer?
  9. Disconnect the battery first so there are no...

    Disconnect the battery first so there are no surprises. $.02
  10. Replies
    4
    Views
    1,234

    What part was welded? The actuator to the...

    What part was welded? The actuator to the housing? Is the tongue fixed to the trailer or is it removable? If welded at the housing, may have to take it to a local welding shop and have to cut and re...
  11. Replies
    15
    Views
    3,591

    Supply your trailer VIN# and it should match with...

    Supply your trailer VIN# and it should match with what left the factory. :yesnod:
  12. Call your local dealer, they can order it for...

    Call your local dealer, they can order it for you. :yesnod:
  13. Replies
    5
    Views
    243

    Too old, they won`t have the molds anymore.

    Too old, they won`t have the molds anymore.
  14. Replies
    5
    Views
    325

    Year Model? :confused2:

    Year Model? :confused2:
  15. Thread: 2000/520vx seats

    by AHens
    Replies
    20
    Views
    2,384

    :popcorn:

    :popcorn:
  16. Replies
    137
    Views
    8,863

    :praying:

    :praying:
  17. Replies
    18
    Views
    905

    :praying:

    :praying:
  18. :praying:

    :praying:
  19. Replies
    30
    Views
    3,259

    :praying:

    :praying:
  20. Thread: 2000/520vx seats

    by AHens
    Replies
    20
    Views
    2,384

    Lighted logo on the back of the seat? Not a...

    Lighted logo on the back of the seat? Not a factory thing in 2000 that I know of. PO must have put them on.
  21. Replies
    4
    Views
    579

    Not a factory RT198P trailer?

    Not a factory RT198P trailer?
  22. Replies
    12
    Views
    641

    :nanner::beers:

    :nanner::beers:
  23. Thread: Oil bath hubs

    by AHens
    Replies
    15
    Views
    1,073

    Lucas Hub Oil $.02

    Lucas Hub Oil $.02
  24. Check and clean electrical connections. $.02

    Check and clean electrical connections. $.02
  25. Replies
    6
    Views
    2,039

    The outer hub for the cap should be 2.33 if it is...

    The outer hub for the cap should be 2.33 if it is the same inner and outer bearing, as what it should be in 2004 with UFP. FYI
Results 1 to 25 of 311
Page 1 of 13 1 2 3 4