Search:

Type: Posts; User: Dkrum

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    536

    If you go on the Ranger website and select the...

    If you go on the Ranger website and select the model that you are interested in, and then choose “build your own”, part of the build tool lets you select custom colors. So you can see the exact boat...
  2. Replies
    2
    Views
    280

    Thanks Don!

    Thanks Don!
  3. Replies
    2
    Views
    280

    Which Hub Assembly Do I Need?

    2017 L4 Verado, 200 HP, Serial # 2B453183 Model # 1201V23ED
    Prop is a 19" Pitch stainless Tempest Plus

    Which is the best hub for this combo? Flo-Torque 2, Flo-Torque 4 or Flo-Torque SSR? Or...
  4. Thread: Network Issues?

    by Dkrum
    Replies
    7
    Views
    392

    Thanks for the help!

    Thanks for the help!
  5. Thread: Network Issues?

    by Dkrum
    Replies
    7
    Views
    392

    Well today everything worked perfectly! So maybe...

    Well today everything worked perfectly! So maybe switching the ports around and then doing a couple of reboots did the trick! I will confirm software versions and IP addresses.
  6. Thread: Network Issues?

    by Dkrum
    Replies
    7
    Views
    392

    Everything is brand new. I did move ports around...

    Everything is brand new. I did move ports around to get this far. I think the two Helix units have the latest software. I can try restoring the factory defaults next.
  7. Thread: Network Issues?

    by Dkrum
    Replies
    7
    Views
    392

    Network Issues?

    I have a new setup in my boat, helix 10 G4n SI at the console, helix 10 G4n DI at the bow, 24 volt terrova with iPilot link, all connected through a 5 port hub. The bow unit doesn’t see the SI, I get...
  8. Replies
    6
    Views
    714

    Thanks, I’ll give that a try!

    Thanks, I’ll give that a try!
  9. Replies
    6
    Views
    714

    489193 Here is a picture of my gauge, thanks!

    489193

    Here is a picture of my gauge, thanks!
  10. Replies
    6
    Views
    714

    Trim/tilt Gauge Is not Accurate

    2013 Merc 150XL Four stroke, Model # 1150F23HD Serial # 2B049721

    My tilt trim gauge barely registers until the motor is well into the tilt range. Is there any adjustment or calibration that I can...
  11. Replies
    2
    Views
    269

    I got it out, thanks. Turns out that there were...

    I got it out, thanks. Turns out that there were two screws buried deep in the carpet.
  12. Replies
    2
    Views
    269

    Front Deck on a Ranger 186 Reata

    Does anyone know how to remove this panel on the front deck of a Ranger 186 Reata? If there are any other screws, they are buried so deeply in the carpet that I can’t find them!
  13. Yes, I do have vault hubs. I checked the inner...

    Yes, I do have vault hubs. I checked the inner grease seal on the back side and they look good. They don’t seem to be leaking grease, but I have 5 years on them so I’m wondering if they are due for...
  14. I have the same boat only with an I4 200 hp...

    I have the same boat only with an I4 200 hp Verado. Trimmed out and running for best fuel economy, I get about 3.4-3.6 mpg with typical loads. So, I think 1.5 mpg seems low. What is your top speed?...
  15. When to Replace Trailer Wheel Bearings vs Clean and Repack?

    I have a 2017 Ranger 1880MS on a single axle trailer. I think that it is about due for maintenance on the trailer wheel bearings. What am I looking for to determine if I need to replace the wheel...
  16. Replies
    7
    Views
    1,367

    Congrats - Let’s see a photo!

    Congrats - Let’s see a photo!
  17. Replies
    26
    Views
    8,344

    plor25 - Your post says that your transducer is...

    plor25 - Your post says that your transducer is fitted "in hull". Are you saying that you have a shoot through hull transducer epoxied in down in the bottom of your bilge? Or is it on the transom on...
  18. Replies
    10
    Views
    721

    Data - That is exactly what I did. today I was...

    Data - That is exactly what I did. today I was out on the lake and I have DI, SI and 2D when I am moving slowly. Once I get over about 6 mph I loose 2D. So I think Wayne P is right, the transom...
  19. Replies
    10
    Views
    721

    Noid - Yes, I do sometimes turn the unit on...

    Noid - Yes, I do sometimes turn the unit on before I launch the boat. Is that harmful? What about the sonar on the trolling motor when I stow it and go from spot to spot? I don't turn the sonar off...
  20. Replies
    10
    Views
    721

    No, I checked that. Good idea though.

    No, I checked that. Good idea though.
  21. Replies
    10
    Views
    721

    Helix 10 Sonar Stopped Working

    The sonar (2d, DI and SI) on my Helix 10 Mega SI G2N has stopped working. GPS, network and all other functions still work normally. My setup includes a Helix 9 at the bow, Ulterra with iPilot Link,...
  22. Replies
    2
    Views
    264

    I tied/taped a chord and to the head unit end of...

    I tied/taped a chord and to the head unit end of the old cable and pulled it through. That worked well. Thanks for the tip!
  23. Replies
    2
    Views
    264

    Installation of a Replacement Transducer?

    The transducer on my Humminbird Helix 10 Mega SI G2N has failed. I have ordered and received a replacement transducer. Any tips/tricks to installation and pulling the cable up to the head unit in a...
  24. Most likely the switches are bad. I have an 1880...

    Most likely the switches are bad. I have an 1880 MS and had the same problem with the indicator lights on many of the switches. Ranger sent new ones under warranty.
  25. Replies
    2
    Views
    539

    Thanks for your reply Wayne! I will look at it...

    Thanks for your reply Wayne! I will look at it the next time that I'm on the boat!
Results 1 to 25 of 49
Page 1 of 2 1 2