two of the four banks on my 10 year old Minn Kota charger decided to take a dump while fishing in Canada. I was able to borrow a couple of chargers to get by. I called Minn Kota on the Monday of my...
Type: Posts; User: gbjake
two of the four banks on my 10 year old Minn Kota charger decided to take a dump while fishing in Canada. I was able to borrow a couple of chargers to get by. I called Minn Kota on the Monday of my...
Thanks. The cable needed is for the livewell remote drain valve.
I have a 2008 Champion 200 Elite. I need to replace the existing Flow-Rite actuator, cable and drain valve. I know the parts I need. Anybody with a similar year and size boat know what the cable...
Given my set up is a separate battery and charger needed for the Garmins? The 31 group AGM battery is a year old.
Thanks for the reply. I also should mention the batteries are Duracell AGM Group 31s.
I received two 106Sv Garmin units from my kids this past Christmas. I'm going to have them installed next month. I'm a casual fisherman at best. I think I was only out 6-7 times last year. I hope to...
Thanks. It's #9 undeer engine cover in the link you sent.
I have a 2013 ETC HO. I'm in need of a upper/lower seal, the rubber gasket between the cowling and lower unit. The serial number for my motor is 0350871. Anybody know how to find out what my exact...
I'm older than I care to admit. I can only stand to fish standing up for a short period of time due to arthritis in my neck. So I have to sit down. I've found sitting down with the foot pedal flat to...
Thanks, What's the best way to get in touch with Mark?
What pitch would you recommend to start?
I have a 2008 Champion 200 Elite with a 2013 Etec HO, Bob's hydraulic JP. Looking to get a 4 blade just for the ride in rough water. I have a 25P tempest plus running 66-70 at 5700 RPMs depending on...
Thanks. I sent Carol an email on 9/25 with a pic. Not heard back yet.
I have a friend with a 2008 Champion 210 elite with a 2008 250 ETEC. One of his gauges crapped out. Any suggestions for replacement? Pic attached
Thanks. I figured it out before I read your message. I tried lube but could not get it back in. The only way I could get it back in was to remove some screws to get access to 2 more screws. One of...
I had another issue happen yesterday with my Ultrex. As near as I can tell the coil cable from the head wrapped around the tension knob used for adjusting height of the motor. I think it may have...
Thanks to everyone for their assistance (billnorman1). This morning I replaced the existing 5 wire flat with a new 5 wire flat. I twisted the 2 extra white wires that were supplying power to the...
The two additional white wires are not used for ground. They both go into the 5th pin, not the female ground pin. Each trailer light has a separate ground wire and is grounded to the trailer. I was...
The white wires in the bundles are not ground. There is a separate white wire for ground. Again I'm not sure why they used white. I'm pretty confident after all of the testing the white wires in the...
I'm pretty sure the existing wiring is as it came from the factory. Not sure why they chose to use white/green/brown and white/yellow/brown wires. The solenoid and the backup lights both get power...
First off I'm an idiot when it comes to wiring and really appreciate all the help. I plugged into the truck. When I plugged in the first thing I tested was running lights. At first they didn't come...
I looked at the wiring diagrams as well as other sites last Sunday and Monday looking for some guidance.
As near as I can tell, the white wire from the white/green/brown bundle is used to supply...
It doesn't appear to have any changes done to the wiring since it was installed at the factory.
I've owned it 5-6 years. Owner of the boat dealer ran the boat for few years.
yes I do have surge brakes. There is a short piece of blue wire connecting to the solenoid. It appears to be spliced with the white wire from the white/green/brown bundle. I pulled a few marker...