Called customer service yesterday and on recorded conversation he stated to { bring oil thats in base to proper level make sure that my prop will allow engine to reach 6000 rpm and find an area that...
Type: Posts; User: skeeterBill200
Called customer service yesterday and on recorded conversation he stated to { bring oil thats in base to proper level make sure that my prop will allow engine to reach 6000 rpm and find an area that...
Thanks for these suggestions I will call customer the dealer tomorrow and see what they say but I will do one of these suggestions for sure cause this can`t right!!
I just completed 10 hr break in and went by the book. Popped the hood this morning and my oil level is 1 1/4 to 1 1/2 inches above the full level hole on dipstick! Soooo now what? My dealer said...
Have to revise this post. Engine was demonstrated for potential buyer at dealer and found hairline crack near heads on block! Somuch to my surprise will have to revise the price to $2500.00 or best...
Repowering my ZX200 with an SHO. Motor is in great condition lower unit is about 3 years old serviced every year. Engine has one year old oxygen sensor and lift pumps one year old. All filters were...
D& B Electric ben there done that ^^^^^^
I had the same type issue with my brakes. I changed brake pads and calipers, bled the lines, new brake oil and it would lock up on me. Turns out some how trash in my actuator was allowing fluid to...
My engine was doing the same thing, it would just die like turning of ignition. Replaced relay switch and it has been flawless ever since. Easy to do!
Yes it turned out to be the switch. I replaced it yesterday and its working flawlessly! Thanks for the replies!
The light on the switch seems to be working properly cause nothing will come on unless it is lit up. I just do not understand why it is intermittently coming on after several presses and or coming on...
I have a 2005 TZX200 with rocker switch panel for electronics. I noticed lately the main switch, the far left rocker switch will not come on till after pressing it in a few times. But once its on it...
First time I changed it at wot the rpms would come down 3 or 4 hundred after about 13 months of use. Brought it in to a local mechanic to see what was wrong, he said he didn`t like the ntk setup and...
I made the conversion from the 0EM O2 sensor to the NTK 21006 plug and play sensor but have had to replace it basically once a year and not hard to do. But I was wondering if anyone has tried the...
I have a 2004 200hp OX66 had the same issue turned out to be fuel pump relay (easy fix)
Just moved dial as you said and unplugged it and placed lectric grease to connector, ran on the hose and seems to be working perfectly!! Thanks for yall input!
Today my tachometer started jumping all over the place it would peg the needle just cruising and back and forth. On dead idle it would show 2000 rpm. Not sure where to begin to diagnose this issue....
Hard to imagine it could go up at all with what I pay already!!!!!
Don`t use any form of grease on these bolts! Use grip washers and loctite only. Trust me been there and done that!!
Anybody in the Houma area that has switched to 4-stroke, with 2 cycle Penzoil pp or Yamahalube wanting to sell any extra on hand? Please call or text 905-688-5970. It`s getting hard to find locally!...
I used 6 drops of red loctite and star washers to assemble
YEP ^^^^^^
I assure you they`re working properly. I`ve tested them several ways, unplug and reverse with shims go remove shims no go! I can actually feel the boat assisting the truck to stop on a downhill. Also...
I have a single axel trailer that I just changed everything but brake lines and I will say that an early morning haul with temps mainly in the 70s my hubs are cool to the touch but later in the day...
That`s how mine started acting up and got more frequent turned out to be fuel relay switch. Just a thought.
Had this happen before, fuse checked out good but contacts ends on fuse holder were corroded. Cleaned those up problem solved.