Search:

Type: Posts; User: jmahaney

Search: Search took 0.00 seconds.

  1. Thread: New Look!

    by jmahaney
    Replies
    21
    Views
    2,795

    Nice rig brother :thumb up2:

    Nice rig brother :thumb up2:
  2. Replies
    24
    Views
    2,698

    I have moved the prop shaft up to 1/2 inch below...

    I have moved the prop shaft up to 1/2 inch below the pad and now the WOT water pressure is between 10 and 12 so I won't go any higher, but I am now hitting 76 fully loaded! (gas gauge even reading...
  3. Replies
    24
    Views
    2,698

    No it was closer to 2 feet than 6 inches. 45km ...

    No it was closer to 2 feet than 6 inches. 45km west winds on a lake that runs east to west, pretty decent white caps Lol But i think we’re missing the point here one thing I’ve noticed with my rig...
  4. Replies
    24
    Views
    2,698

    To be honest, they may not have been 2 footers...

    To be honest, they may not have been 2 footers where i was running open but it was still stupid rough. Trim down a little and hammer it the 21XD handles some dirty water. It's really not that hard...
  5. Replies
    24
    Views
    2,698

    I dunno man it was rough, rough enough i...

    I dunno man it was rough, rough enough i wasn't holding it. :laugh:
  6. Replies
    24
    Views
    2,698

    So went out today about 1/4 inch higher on the...

    So went out today about 1/4 inch higher on the jackplate, the absolute highest i can go now before going down a hole on the motor. It was super windy so it was hard to punch it for long but I...
  7. Replies
    24
    Views
    2,698

    Sounds good, I will be installing the gauge...

    Sounds good, I will be installing the gauge today. I blew out the lines last night cleared all the gunk, but the gauge itself was definitely no good. I'll make the swap and see how it goes. I am...
  8. Replies
    24
    Views
    2,698

    Fair enough, the feedback is already appreciated....

    Fair enough, the feedback is already appreciated. I’ll have to make the best guess at a second prop and hope for the best, I’ll install a water psi gauge here too and get the motor up some
    more....
  9. Replies
    24
    Views
    2,698

    Yeah I don’t know what to tell ya but the poles...

    Yeah I don’t know what to tell ya but the poles changed it about 1mph, didn’t affect hole shot at all. They are only 8 footers and ported holes to lighten the poles, I was fully aware expecting to go...
  10. Replies
    24
    Views
    2,698

    Right, the motor can spin 6000 no problem. ...

    Right, the motor can spin 6000 no problem. 5800 being ideal. The power poles believe it or not didn't slow the boat down noticeably at all. Probably went from 74 to 73 and change. The poles...
  11. Replies
    24
    Views
    2,698

    When I read the manufacturer recommendations on...

    When I read the manufacturer recommendations on the Bravo XS they say to go up 2 pitches to replace the Bravo 1 which is currently on the boat, would I not in theory gain rpms going up to a 29...
  12. Replies
    24
    Views
    2,698

    Fair enough, from what ive read the bravo xs...

    Fair enough, from what ive read the bravo xs turns higher rpm than the comparable bravo 1 so that's an interesting option for sure
  13. Replies
    24
    Views
    2,698

    Thanks for the reply, I'll get working on the...

    Thanks for the reply, I'll get working on the water gauge right away. I am told 5800 rpm is the sweet spot on this engine but I believe the limiter is 6200. I would definitely be more than happy...
  14. Replies
    24
    Views
    2,698

    Help setting up 2004 21XD

    Hey guys, I've been lurking the bullet forums since I bought my 21XD last spring. I have been super happy with the ride, very dry and a great rough water boat. I have run Tritons, skeeters,...
  15. Replies
    2
    Views
    602

    right now im leaning towards the 24 raker 2 .....

    right now im leaning towards the 24 raker 2 .. but if any fellow g2 owners experience to share im all ears
  16. Replies
    2
    Views
    602

    Etec G2 150 H.O prop help

    Hello,

    I have a Trition TR 186 that was running 62 mph (gps) with a Mercury 150 optimax (long shaft) .. unfortunately it needed a rebuild so I decided to repower with a new 150 H.O G2. The old...
  17. Replies
    9
    Views
    797

    yeah exactly.. so it's not in the way. I haven't...

    yeah exactly.. so it's not in the way. I haven't had a chance to look at the motor yet, ill take your advice and remove the bow gaurd and make sure the pin is pressed all the way down so the lock...
  18. Replies
    9
    Views
    797

    The rope doesn't seem to be in the way at all....

    The rope doesn't seem to be in the way at all. I'll remove the bow guard this weekend and see if I can figure out what's happening. Thanks for the response guys!
  19. Replies
    7
    Views
    647

    I also found that the walmart everstarts are...

    I also found that the walmart everstarts are absolutely great! beats any other battery i have used.
  20. Replies
    9
    Views
    797

    Yes at one point the bow guard was taken off. I...

    Yes at one point the bow guard was taken off. I guess I don't know what the properly installed safety lock should look like to tell you what position it needs to be in, but on second thought if I...
  21. Replies
    9
    Views
    797

    that's exactly the piece that seems to be...

    that's exactly the piece that seems to be sticking. I don't recall taking anything apart that didn't require coming apart. The mount latched fine when i replaced the rope for a while after, this...
  22. Replies
    9
    Views
    797

    Minnkota Fortrex Mount problems

    Hey Everyone,

    I am having trouble with my Fortrex mount, at some point last year I replaced the rope and shortly after I was having trouble getting the trolling motor to lock properly in the...
Results 1 to 22 of 22