Mine did the same for a couple months. It rubs right off & will stop after it wears some. Dealer told me this same thing a few months ago
Type: Posts; User: Mountainman
Mine did the same for a couple months. It rubs right off & will stop after it wears some. Dealer told me this same thing a few months ago
Solix on FX & Helix on ZX is what I heard
I was talking to a Yamaha repair guy at the Classic last weekend.....Check your fuel line in the rear compartment. If the bulb & a section of hose is laying below the level of the fuel tank, i.e. in...
Ahhhh.....Good info. Thanks
If you have Lowrance Carbon units, the Bluetooth capabilities are in the graph. Nothing else is needed if that's the case.
It is the entire carpet wrapped piece. Complete separation from fender. But it does appear to have been glued in place originally
Did not see a listing in props for sale. In need of another 25. IS this still available? If so, PM me your info.
Saw a reference to the inner fender (carpeted piece) coming loose on new Skeeter trailers a few weeks ago in another post on here. Noticed mine (2018 FX21) was popped out on starboard side front AND...
I understand your displeasure over past experiences......mine with Merc are a good part of the reason I now have a SHO. All my Merc issues were covered under warranty, but it left me with little...
I had a 2011 721 (prior to deck changes) and I can tell you theres a lot of room on one. Im about 250 & my buddy is about 230 (both short & wide shouldered). We could lay 10 rods on either side &...
That's the beauty of the MM.....theres virtually no movement either direction. The design doesn't allow the motor to move at all......very very little. I see much less side to side movement with MM...
I have an 18 FX, but no dealings with Skeeter or Skeeter trailers previously. I asked Skeeter rep about issues I've heard from other owners regarding the need to balance trailer tires. According to...
I had an issue with the Ultrex curly cable hanging up on the Durasafe lock. Anyone have the same issue or a fix for it?
Anybody tried various props on their FX boats? Almost through break-in on my FX21 & was wondering if there was a better prop out there than the T2 for these hulls. Otherwise, I suppose a lil B&B love...
I replaced both bow & console plastic plates with water jetted, 316 stainless copies on my 721. Factory ones were not glued, but were stuck pretty good coming off. Small flat tip screw driver pried...
Indeed a very good dude.
From what I experienced installing my MotorMate this weekend, it does allow you to tilt down farther. Its not a huge difference, but I could not clear the top of my garage with the ProRule, got about...
Couple of trips out with the prorule now & I'm going back to motormate. It locked the merc on my last rig down with zero movement. No reason to think it'll be any different with the yammie.
Word of advice....when tubes are removed, the opening left is pretty ragged fiberglass & there is quite a bit of wiring exposed in the nose of the boat. I have removed the tubes from all my previous...
Nevermind.....digging a lil deeper, the "arm" I was seeing is the drain line from the rod box/deck lip. Take 2 faceplate screws out, push down on rod tube cluster & pull toward rear of boat. Slides...
Anyone removed the rod tubes in a newer fx? Not sure if the '18 models are the same as previous years, but 2 screws in face plate and an arm going into center box?? Any ideas?
Picked up my new ride yesterday & put an hour on break in. Still a long way to go on that, but any suggestions on a ballpark figure where to start on the prop to pad? Atlas hydraulic with gauge, so...
So, MotorMate eliminates the need for the steering clips on the Yammies?
Think I have traded for a 2018 FX21. Whats the typical prop to pad set up you guys are running and real world speeds with tourney load & 2 guys? Thanks in advance!
Too bad they ruined a nice boat by putting a stupid bowtie on it!! LOL