I would like to chime in on this topic with my issues FWIW. I tried to download an update for my 2017 LakeVu Ultra card through Garmin express and it would fail at 70-80% every time..always getting...
Type: Posts; User: dhuggins
I would like to chime in on this topic with my issues FWIW. I tried to download an update for my 2017 LakeVu Ultra card through Garmin express and it would fail at 70-80% every time..always getting...
Viper I appreciate the reply. I'm glad I'm not the only one! However I did talk to Dennis from Dexter (DABS) and he has already got me some new wear sleeves o-rings and seals coming. Hopefully this...
Yes sir I will do! I cannot believe I missed that wear sleeve. To the untrained eye that looks like it is all one piece and just how the spindle is made..I am kicking myself in the butt.
These are vault hubs from UFP. Th grease is injected through a zerk fitting that screws into the end of the spindle. You fill that up until grease comes around the bearings. Remove the fitting. Fill...
309571
Is this it?
Dabs I honestly wasn't aware of this as I can't find it in online..do you by chance have a part number?
Ok hammer..i removed them to address one issue at a time. It is only temporary not permanent. I posted for help not snarky replies.
Thanks fidget..its been a pain definitely
I have all new brake lines Marine Master sent me since that was the last thing in the system it could be. I have now since removed the brakes for the time being to get the issue with the seals...
I checked the brake line if that's what you are referring to. The brakes are no longer a factor since I have removed them.
Guys looking for some advice..I am having some issues with a 2016 Marine Marine Master Trailer tandem axle under a Phoenix 920 ProXP that has been going on for about 6 months. I got this boat from a...
Please delete I am moving this to the Phoenix Boats page.
Guys looking for some advice..I am having some issues with a 2016 Marine Marine Master Trailer tandem axle under a Phoenix 920 ProXP that has been going on for about 6 months. I got this boat from a...
If you get a meter out and check voltage on each of the terminals on the connections of your truck you can eliminate your truck being the issue. (Push the brakes in and make sure you have 12v on the...
I suppose I probably could but I guess this is the best way for them to ensure a quick turn around. Just grab one off the shelf they already have ready to go. Doesn't really matter to me if I get a...
Word of advice..don't try to update the Fusion Black box through your graph...
Called support and did some things to it at lunch but to no avail. The said its a software issue and are sending me a refurb unit. Great customer service support though none the less..
https://s14.postimg.org/tt38h3bsd/20161103_201325.jpg
https://s14.postimg.org/vm655ewz1/20161103_201345.jpg
Last night I hooked up the black box via nmea to my network. Everything was working fine using one of my 7610xsv at the console. Per manufacturers recommendations downloaded the latest software...
So you don't get any interference on the sensor at the bow from the armature in the trolling motor???
Also there is no puck in your last picture??
Troyboy is that your Airmar heading sensor on the bow by your trolling motor and the Garmin 19 external GPS antenna at your bilge?
As long as they are of the same type, age and state of charge then it is ok. If there were huge voltage inbalances then there would be issues but then the processor would shut it down because the...
Disagree..they have on board diagnostics that regulate the output.
Instead of each individual battery having its own leads..why not use a 36V charger and charge all the batteries in series? Then you only need 2 banks (1 for trolling batteries and 1 for cranking). I...
I had an issue with a thru hull fitting being cracked. When I would pull my plug there would be quite a bit of water that would come out. I could not figure out where it was coming from so I put the...
Again the ENTIRE spring was coated in gatorhyde...not that easy