Search:

Type: Posts; User: PowerPoleTech

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    130
    Views
    12,903

    My apologies, I did not see your question. ...

    My apologies, I did not see your question.

    Unfortunately, due to mounting location requirements I cannot say for sure how many holes if any would line up for your installation based on where your...
  2. Replies
    130
    Views
    12,903

    I just wanted to chime in here about the UMP. Out...

    I just wanted to chime in here about the UMP. Out of the box the Move will mount on any boat without the need for the UMP. Simply drill your holes and mount the Move. It is not required for...
  3. Randy - The Charge enters a sleep mode as long as...

    Randy - The Charge enters a sleep mode as long as everything is off and there is no power draw on any of the battery banks and the boat is not in motion. If it is not plugged into AC and there is a...
  4. Yes, the Charge was designed to be plugged in to...

    Yes, the Charge was designed to be plugged in to AC when not in use. Once the Charge has performed its charging cycles it will enter a sleep mode and just maintain the batteries as needed.
  5. jozmon - I believe what you are seeing is the...

    jozmon - I believe what you are seeing is the balancer kicking on and off at small amounts of amperage. The balancing is the final step and will cycle to continuously check the batteries.

    Once...
  6. Replies
    16
    Views
    868

    It was a fix for increased AH input for lithium...

    It was a fix for increased AH input for lithium batteries over 130 AH if wired in parallel or over 130 AH. The previous max was 130 AH and it would not allow the user to enter a higher value.
  7. Replies
    11
    Views
    1,125

    Clayton - It sounds to me like the other pump did...

    Clayton - It sounds to me like the other pump did not get the firmware update. I would try removing the fuse to the pump that is working correctly and then try to connect to the pump that needs the...
  8. I believe it was originally set to 32F. Keep in...

    I believe it was originally set to 32F. Keep in mind that is at the sensor on the board in the pump so surrounding temp could be less or more given the circumstances.
  9. Matt - You are correct, in cold temperatures the...

    Matt - You are correct, in cold temperatures the DOWN operation is limited until ambient temperature is above the threshold. Simply holding the UP button for 10 seconds or so will warm them up enough...
  10. Replies
    40
    Views
    3,383

    I do not normally chime in on these threads, but...

    I do not normally chime in on these threads, but your statement is not accurate. We have not used a 433mhz since CM1 products almost 4 years ago.

    All of our products operate on CM2.0 with a...
  11. Replies
    4
    Views
    475

    Astyle - The current connection with compatible...

    Astyle - The current connection with compatible anchors to HDS units is through bluetooth connection. The down side to Bluetooth is limited range, signal strength and number of connections. All of...
  12. Replies
    9
    Views
    986

    It can take some time to fully bleed the lines,...

    It can take some time to fully bleed the lines, depending on how much room and how far they can deploy on the trailer.

    I wanted to eliminate the problem of it being a controller or a signal issue...
  13. Replies
    9
    Views
    986

    Give us a call at 813-689-9932 opt 2 and we'll...

    Give us a call at 813-689-9932 opt 2 and we'll walk through a few things for you to check. Does the problem persist with all of the controllers no matter where you are on the boat?
  14. Replies
    13
    Views
    963

    Chad - We have had customers get rid of a 12v...

    Chad -
    We have had customers get rid of a 12v battery in some cases where they were running two as a house battery and cranking battery. We have also had customers report going to 24v systems...
  15. Replies
    9
    Views
    986

    Do you know if these are CM1.0 or CM2.0? Have...

    Do you know if these are CM1.0 or CM2.0?

    Have they always done this or is this a recent issue? Have your tried doing a firmware update recently?
  16. Replies
    4
    Views
    433

    The 1.35 update was to improve the balancer when...

    The 1.35 update was to improve the balancer when using individual 12v batteries for the trolling motor. It doesn't change anything for applications with single 24v or 36v litium batteries.
  17. Replies
    11
    Views
    2,189

    Zack was not using a Power-Pole Charge on the...

    Zack was not using a Power-Pole Charge on the boat in question. However, we are sending him one for his new BassCat.
  18. Replies
    11
    Views
    1,684

    mxmike - Auto operation still works as normal...

    mxmike - Auto operation still works as normal with single-tap auto enabled. Just a timing thing that once the button is held longer than the single tap duration it will ignore and run as manual. I...
  19. Replies
    8
    Views
    683

    DEFMP - That looks to me like something got hot...

    DEFMP - That looks to me like something got hot enough to melt the hoses, especially for there to be holes in both the up and the down hose in the same locations. Were the hoses resting against a...
  20. No issue with this other than the need to add an...

    No issue with this other than the need to add an extra battery ON/OFF switch to kill power when not in use or when charging batteries.

    It may also be possible to get a low voltage signal on the...
  21. Replies
    7
    Views
    719

    5 Alive - When did you perform the update and...

    5 Alive - When did you perform the update and what app did you use? When the feature was first released, we did have an issue with that, but is was quickly resolved to my knowledge.

    I would try a...
  22. Replies
    7
    Views
    719

    The single tap auto only works for CM2.0...

    The single tap auto only works for CM2.0 controllers.
  23. Replies
    7
    Views
    719

    munchie, The controllers need to be updated to...

    munchie,

    The controllers need to be updated to the latest firmware and they need to be set to single tap function.

    Start by downloading the C-Monster app and update the firmware (2.02) on the...
  24. Replies
    6
    Views
    3,538

    The amp draw while anchored or stowed is less...

    The amp draw while anchored or stowed is less than 20 milliamps. The main amperage draw is only while the pump is cycling the anchor up or down.
  25. Unfortunately this cannot be done, completely...

    Unfortunately this cannot be done, completely different Rf frequencies and radios. Your system is only wireless capable with the addition of a Magsync receiver. This will give your two wireless key...
Results 1 to 25 of 281
Page 1 of 12 1 2 3 4