Search:

Type: Posts; User: Ole Guy

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    1,443

    Thank you for all the answers to my request....

    Thank you for all the answers to my request. Haven’t replied sooner as I just got out of surgery yesterday. Six to eight weeks recovery so I have time to research. Thank you everyone.j
  2. Replies
    20
    Views
    1,443

    Thank you to all the great reply's. I can't use...

    Thank you to all the great reply's. I can't use the tongue because it is a tuck under & I use it to be able to close my garage door. To attach the steps to the winch stand, the winch stand would have...
  3. Replies
    20
    Views
    1,443

    Thank you

    Thank you
  4. Replies
    20
    Views
    1,443

    Steps or latch lock for BassBoat to trailer

    Have back issues & having surgery so looking for recommendations to easier access to hook & unhook winch strap & loading & unloading my 2004 Champion 187. Steps or bow latching system? Steps would...
  5. Thank you

    Thank you
  6. 5600-5800 DI about 7 MPH

    5600-5800 DI about 7 MPH
  7. No

    No
  8. 187 Champ with 150 DI Evinrude lost speed, need help.

    Need help. My 187 Champ is is excellent condition. Just had a tune up on my 150 HP Evinrude with new plugs, compression tested 5 cylinders 100% & 99% on1. Does not seem to have the speed it used to....
  9. Replies
    3
    Views
    271

    Thanks John

    Thanks John
  10. Replies
    3
    Views
    271

    ULTREX Circuit Breaker for TM

    I had a FORTREX/101/36V and replaced it with a new ULTREX 112/36V. I noticed the recommended TM CB is 60A for The ULTREX as it states it can draw up to 52 Amps & I currently have a 40 Amp circuit...
  11. Replies
    3
    Views
    243

    I had the same question, so when at a tournament...

    I had the same question, so when at a tournament I asked all the boaters that had an ULTREX, why they located their heading sensor in the location it was in. Their reactions were numerous: don't know...
  12. Replies
    5
    Views
    253

    Is there a constant elec draw on the heading...

    Is there a constant elec draw on the heading sensor & should I install a disconnect & fuse?
  13. Replies
    5
    Views
    253

    Thank you

    Thank you
  14. Replies
    5
    Views
    253

    Ultrex Heading Sensor install location

    I am not sure where to locate my heading sensor for my Ultrex. I have a Champion 187 & was thinking of locating it on the bow area because there is no place to mount it behind the drivers seat. I...
  15. Thread: Prop advice

    by Ole Guy
    Replies
    1
    Views
    285

    Thank you

    Thank you
  16. Thread: Prop advise

    by Ole Guy
    Replies
    1
    Views
    194

    Prop advise

    I have a 2004 Champion 187 DC, 150 Evinrude DI, 2 Power Poles, 10" Man Jack. Run average weight with self at 56 W.O.T. @ 5450 RPM with 23 Tempest, slow out of the hole. Cavitation plate 3-1/4" below...
  17. Replies
    9
    Views
    1,059

    How much for the 24 & what condition is it in?

    How much for the 24 & what condition is it in?
  18. Stainless Steel Cotter Pins for 2004 Evinrude 150 Prop Shaft

    What is the proper size Stainless Steel Cotter Pins used on 2004 Evinrude 150 Prop Shaft?
  19. Thread: Four Stroke

    by Ole Guy
    Replies
    9
    Views
    438

    Thank you. I will drain some oil until its in...

    Thank you. I will drain some oil until its in range.
  20. Thread: Four Stroke

    by Ole Guy
    Replies
    9
    Views
    438

    Four Stroke

    Changed oil & filter in my Mercury 25 HP Four Stroke. Manual said 1.9 quarts oil. I added both quarts, will that be a problem? If so what should I do? Any help if this is a problem, I appreciate it....
  21. Replies
    7
    Views
    147

    Thank you

    Thank you
  22. Replies
    7
    Views
    147

    Thanks

    Thanks
  23. Replies
    7
    Views
    147

    2004 187 Live Well

    I would really appreciate some help with my 2004 Champion 187CX live well system. :praying:

    My live well valve switch has 3 positions: Re-circulate, Empty & Automatic. I have 2 pump switches;...
  24. Replies
    4
    Views
    192

    Thanks everyone.

    Thanks everyone.
  25. Replies
    4
    Views
    192

    187 Live well system

    I would really appreciate some help with my 2004 Champion 187CX live well system. :praying:

    My live well valve switch has 3 positions: Re-circulate, Empty & Automatic. I have 2 pump switches;...
Results 1 to 25 of 34
Page 1 of 2 1 2