Fred, it's always good to hear from you. Contacted C&O, talked to Christin, That particular hub and plate is not available anymore. Guess I'll just look like another Redneck pull'in a boat without...
Type: Posts; User: ogcj
Fred, it's always good to hear from you. Contacted C&O, talked to Christin, That particular hub and plate is not available anymore. Guess I'll just look like another Redneck pull'in a boat without...
I have a 03' 196 with tandom trailer. I need the plastic hub, about 6 3/8" round with 2 1/2"
hole in center for grease fitting. It has one screw that screws in the wheel for holding it on. Also the...
Economics 101. They have to sell enough boats to meet expenses. They haven't done it and I doubt they'll do it any time soon. It's not them, it's the US economic turmoils we're experiencing. Genmar...
Thanks for the reply John. Be nice to get a few other responses to see what others do.
BRP Fuel System Cleaner and BRP 2+4 Fuel Conditioner.
What's the difference?
When should one or both be used?
Does anyone put these in the tank at every outing, if so which one?(most important)...
Champer 196, My boat is just like yours, same year and motor. Great fishing machine, not so good on speed. Cyclone prop 23 gets 62mph with instant lift. My eyes never loose contact with the water and...
I was wrong about the location of this nut. It's not on the steering bar. It's on the frame that connects to the jackplate, which is under the front side of the motor, right behind the steering...
Hey Fred, good to hear from you too. OK, which one is best for my boat and motor? I respect your opinion, shoot straight.
Does anyone use the Rude motor bracket and a transom savor together? Is it best to use one or the other and not both? Appreciate your opinion and how you do it. Thanks
03' 200 DI. I imagine this has been talked about before, just can't find anything on this subject. The very large nut (starboard) next to the hydro steering seal was was about one full thread loose,...
I think every boat has this problem eventually. The glue is good for a temp fix and might hold forever, who knows, but if you could replace the seal at an affordable price that would be best, and you...
I'm trying to run (test) a Trophy P prop on a 200, '03 Evinrude and need to know what to buy to make it work correctly. Part names is appreciated, I'm kind of a layman at this. Many thanks.
Sandy
Cool tape. This different than the one I have. Reggie has the DVD of the other one, maybe he'll put it on the board. I'd do it, but don't know how.
Seahorse, thanks for replying quickly. I bought some grease just for this if needed, it will be used. The plug with the rust was top starboard, don't know the cylinder #'s. (I guess I need to know...
Rusty. seahorse, ruditech, Fred, any of you knowledgeable folks, need a ? answered.
Just changed my plugs in an 03' Rude 200 DFI. Noticed one plug was corroded with rust on the end. Can I use...
Motor: '03 Rude 200 DFI. I don't seem to have any current problems, but the future is a concern to me about Ethanol 10%. Would something like BRP 2+4 added wth each tank be good or bad? What would...
Fisher, Where did you get a see through filter for the boat. I assume your talking about the large canister type (oil filter size). I've thought about that in the past, but can't find one. That's the...
How does the new E-Tec compare with the DFI in gas useage. I presently get about 6.5 at 4500-5000. I've calculated it several times and it's pretty consistent. Compared to my previous (OMC) carb...
I saw somewhere on here the Teleflex trim control was discussed. My question is, how hard is it to install the single control on a 03' Champ196 with a Rude 200. Is this something I can do without...
deadringer6 (Carl), Your doing a grand and honorable thing with this site. I commend you, as others do with the effort your putting forth for all veterens. God bless America and our military.
Sandy
U.S. Navy 64-67.