Hello took the new rig out for the first time yesterday and when you hit anchor mode on the ghost it just takes off running at a higher speed. Is there some kind of calibration that needs to be done...
Type: Posts; User: Ddsmith
Hello took the new rig out for the first time yesterday and when you hit anchor mode on the ghost it just takes off running at a higher speed. Is there some kind of calibration that needs to be done...
Thanks bigbson I’ll check that.
Hello all trying to determine if I’m having a motor issue or prop/setup issue. Boat is a 2015 skeeter zx225
I have ran 2 different props a 25p tempest and a solas 25p I just had cupped and...
Hello all trying to determine if I’m having a motor issue or prop/setup issue. Boat is a 2015 skeeter zx225
I have ran 2 different props a 25p tempest and a solas 25p I just had cupped and...
It does stay outside in a open pole barn, I trim it up and down multiple times after use and store it trimmed all the way down when it’s parked to try to insure all the water is out. I do always warm...
No doubt mine has 2 oil leaks, one is to believed to be a cracked port head. Funny part is no one can tell me why if happened. Never been overheated or anything like that, it’s crazy for a head to...
Thanks for the reply’s I appreciate it.
Since it has gotten colder I have noticed in the last couple of trips out my SHO idles about 300 rpms higher than normal especially on the first crank of the day. Is this normal for the SHO or a 4...
The cover could be cracked I didn’t see a crack but I also didn’t remove it from the motor so that’s a possibility. I happened to find the leak while I was looking for another leak on the port side...
Has anyone had any issues with valve covers leaking oil? I have searched the web and can’t seem to find anything. If so is there a reason behind it other than just wearing out?
Hello all I noticed a small amount of oil on the port side of my motor it’s circled in red. There was more oil there but I had cleaned it up before I thought to take a pic. Also noticed a small...
So my T1 25 on my 225 sho is done (cracked hub housing). Looking to get a new prop and was thinking of going with a mercury prop, probably going to try to pick one up here in the next few days....
So my T1 25 on my 225 sho is done (cracked hub housing). Looking to get a new prop and was thinking of going with a mercury prop, probably going to try to pick one up here in the next few days....
Thinking of going with a solas scorpion to get me by for the time being, does anyone know what thrush washer or any other hardware I will need?
423647
Thanks for the info, I guess I should have put this in my OP the prop I have had a amazing hole shot and Top end is around 68-69. So wouldn’t going to a 4 blade slow my top end down some? I’m only...
I’m running a T1 25p prop on a 2015 225 SHO. I noticed today that the casting around the hub has 3 cracks. They are right beside the 3 stand off that go out to the prop itself ( if that makes any...
Hello, I have a buddy that’s got a 06 hpdi 250. The lower unit along with the prop and all the hardware was replaced late last summer when the prop shaft broke off. He was in his shop today and just...
Hello all I just got a new boat and am running 2 gen2 9’s and a 9 carbon. The guy that had it before me had the fish ID turned on the 2 gen2’s. I’ve turn both of them off but they keep beeping when...
Yes I dropped it down to 3.25 and got 69 out of it loaded. I am still trying to fine tune it but I got to get my prop worked first it has a couple dings in it that I figured are hurting it on top end
Measured the pro to pad and came up with 2.25 in, so with it being that high and hard to turn at wot I dropped it down a inch and am now running 69 fully loaded. That’s a good improvement I am going...
Thanks also noted that the boat is very hard to steer at wot
Thanks for the info guy I plan on running it Friday. What is the minimum water pressure for the SHO? This is the first one I have had.
Thanks something else I noticed that may also point to the motor being to high is it throws a pretty high rooster tail
I’m running a 15 zx225. Motor has a T1 25 pitch prop. It’s turning 5900-6000 depending on the load. 67 solo and 62 with 2 big guys. Water pressure is 18-20 lbs depending on where the motor is trimmed...