Search:

Type: Posts; User: DABS

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    1,179

    If your axle is round or was made by Reliable, it...

    If your axle is round or was made by Reliable, it will take the L68111 race.
  2. Thread: What do you do

    by DABS
    Replies
    75
    Views
    2,739

    Gorilla glue

    Gorilla glue
  3. Replies
    37
    Views
    2,934

    Luckily they ship return labels with the product....

    Luckily they ship return labels with the product. Wonder if they get used?
  4. Replies
    12
    Views
    1,179

    5 lug wheel should be L68149 with L68110 race,...

    5 lug wheel should be L68149 with L68110 race, and L44649 with L44610 race
  5. Replies
    3
    Views
    520

    The stainless steel sleeve is used on all UFP...

    The stainless steel sleeve is used on all UFP axles as a replaceable wear piece. The spindles are the same diameter as the grease and oil bath. The sleeve is replaceable rather than having wear on a...
  6. Thread: Spindle Sleeve

    by DABS
    Replies
    8
    Views
    540

    Not all spindles are manufactured with the o-ring...

    Not all spindles are manufactured with the o-ring groove. Red RTV is preferred in either case. If you do not have a groove, use it anyway to keep extra protection from the rear. You can also use...
  7. Replies
    57
    Views
    2,652

    I have the Black and Decker Ranger with the...

    I have the Black and Decker Ranger with the shotgun shell batteries, 7V... hmmm might be time to upgrade?
  8. Thread: Surge brakes

    by DABS
    Replies
    12
    Views
    936

    If the pushrod loses the clip or pin at the end,...

    If the pushrod loses the clip or pin at the end, it will be an on/off effect with no progressive brake in between. Remove the pushrod and try pulling the two pieces apart. If they separate, replace...
  9. Replies
    28
    Views
    2,666

    Not saying it's the same problem but once air...

    Not saying it's the same problem but once air gets into the cylinder it seems to get trapped at the top. I just add more hydraulic fluid and cycle it a few times and it corrects the problem every...
  10. Thread: Surge brakes

    by DABS
    Replies
    12
    Views
    936

    Replace the pushrod/spring assembly

    Replace the pushrod/spring assembly
  11. Replies
    9
    Views
    804

    won't hurt it to lube, help keep it from rusting...

    won't hurt it to lube, help keep it from rusting too.
  12. I'm with Highcentered on this. We were asked to...

    I'm with Highcentered on this. We were asked to leave 2 different dealerships in one night because all they wanted to know was our preferred payment each month. They wouldn't say the price on the...
  13. Replies
    28
    Views
    2,666

    My tractor does that but only when it's low on...

    My tractor does that but only when it's low on hydraulic fluid....just sayin
  14. Replies
    11
    Views
    779

    The only difference between a single disc or...

    The only difference between a single disc or drum, is the solenoid which is necessary on a disc, but not on a drum.
  15. Replies
    5
    Views
    453

    Look on the back side of the rotor. If they are...

    Look on the back side of the rotor. If they are UFP they will say so or if Tie Down it will have a TDE stamped on it.
  16. Thread: Hitch Drop

    by DABS
    Replies
    48
    Views
    3,073

    1" above is still acceptable. Better above than...

    1" above is still acceptable. Better above than below.
  17. Replies
    5
    Views
    453

    they were going back and forth with UFP or TIE...

    they were going back and forth with UFP or TIE Down back then UFP rotor measured 9.75" across.
  18. Replies
    12
    Views
    4,584

    The hub should be stamped with the manufacturer...

    The hub should be stamped with the manufacturer stamp. TDE is Tie Down but all UFP hubs were stamped on the back side back then.
  19. Replies
    15
    Views
    4,799

    If it's a torsion arm, try swapping it out with...

    If it's a torsion arm, try swapping it out with another. If it still wears, the axle tube is bent
  20. Replies
    5
    Views
    2,630

    no it is not. Only the pads cross to the 91...

    no it is not. Only the pads cross to the 91 Dodge Daytona or Plymouth acclaim. The caliper is different. Call Cindy @ 931-967-5101 and ask her for the old Chrysler cross on calipers.
  21. Thread: A60 Actuators

    by DABS
    Replies
    13
    Views
    795

    The reason for pulling forward is to allow the...

    The reason for pulling forward is to allow the piston in the master cylinder to return to zero, against the snap ring. This protects the honed cylinder and keeps it from rusting. A rusted cylinder...
  22. Replies
    7
    Views
    512

    YES

    YES
  23. Replies
    12
    Views
    2,104

    it is a static shock, not gas.

    it is a static shock, not gas.
  24. Thread: Cool Hubs

    by DABS
    Replies
    4
    Views
    609

    same hub, bearings and seal. Only difference is...

    same hub, bearings and seal. Only difference is the contents (grease), and the protector.
  25. 91 Plymouth Acclaim or Dodge Daytona, front brake...

    91 Plymouth Acclaim or Dodge Daytona, front brake pad
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4