Search:

Type: Posts; User: josie201

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Rotor

    by josie201
    Replies
    1
    Views
    180

    Rotor

    Need to replace the rotor and caliper on a 920 phoenix trailer. Any body know what material they are made of. Zinc, stainless or aluminum

    thanks
  2. Replies
    5
    Views
    206

    I am just didn’t go into the details

    I am just didn’t go into the details
  3. Replies
    5
    Views
    206

    Ok, thanks for the help

    Ok, thanks for the help
  4. Replies
    5
    Views
    206

    First start after service

    Serial# 2B362821

    Motor will be unused for a little while, as my injectors are being serviced. Is it a good idea to do an oil prime once things are reassembled, before the first start. I have the...
  5. Replies
    6
    Views
    219

    Did he bypass the fuel selector valve in the...

    Did he bypass the fuel selector valve in the bilge, and tie the one straight into the motor
  6. Replies
    6
    Views
    219

    maybe boat salvage yard. Wonder why he took it...

    maybe boat salvage yard. Wonder why he took it out?
  7. Replies
    13
    Views
    683

    for sale? Listed where?

    for sale? Listed where?
  8. Replies
    6
    Views
    219

    Pretty sure they are 25 gallons, at least mine...

    Pretty sure they are 25 gallons, at least mine are. The fuel selector valve has leaked twice on mine and have gone to a manual 3 way valve set up. That may be why you only have one tank , selector...
  9. Replies
    6
    Views
    421

    duct tape acceptable

    duct tape acceptable
  10. Replies
    6
    Views
    421

    Injector service

    Serial #2b090964

    Anything special i need to cover up if I remove fuel rails and injectors, when sending out for service? May be 3 to 4 month before things would be reinstalled
  11. Thread: Fuel lines

    by josie201
    Replies
    1
    Views
    186

    Fuel lines

    Serial #2b090964

    I have an older stratos that the fuel tank divider has started to ooze fuel. Replacing with a brass 3 way valve. Can I use a small amount of dawn soap on the valves barbed...
  12. Replies
    5
    Views
    376

    Thanks to both. What I want to accomplish is keep...

    Thanks to both. What I want to accomplish is keep my foot on the pedal for steering, start and start with thumb or finger. Like a jog mode, but don’t want to be in spot lock mode
  13. Replies
    5
    Views
    376

    Motorguide Mode Of Operation

    Have the tour right now, thinking about tour pro. For those that have the tour pro, can I use the remote to adjust speed and do foreword and reverse. I want to leave my foot on the pedal for steering...
  14. Thread: Seat post

    by josie201
    Replies
    1
    Views
    150

    Seat post

    Do they make a seat post that will go up and down, and also allow me to tip the butt seat to various angles (lock in place at preferred setting) 3/4 or so post mount base is in the boat now
  15. Replies
    5
    Views
    172

    try this one

    try this one
  16. Replies
    5
    Views
    172

    Didn’t notice water from motor mount area, but...

    Didn’t notice water from motor mount area, but what we noticed was water at rear of motor coming out of gasket area. The one original gasket was slightly different than the new one, notice old was...
  17. Replies
    5
    Views
    172

    Picture of the other gasket, the replacements...

    Picture of the other gasket, the replacements look like this one525104
  18. Replies
    5
    Views
    172

    Power Head Gaskets

    Serial #2B362821, and 2B090964

    Power Head Gaskets from our 2 motors, why the differance? The one that is showing the tear directly behind the lower crank case seal location, could that be why we...
  19. Thread: Torque Values

    by josie201
    Replies
    12
    Views
    374

    much appreciated

    much appreciated
  20. Thread: Torque Values

    by josie201
    Replies
    12
    Views
    374

    Those would be at 25 ft lbs

    Those would be at 25 ft lbs
  21. Thread: Torque Values

    by josie201
    Replies
    12
    Views
    374

    Would that be #5 and #6 in the torquing sequence

    Would that be #5 and #6 in the torquing sequence
  22. Thread: Adapter paint

    by josie201
    Replies
    3
    Views
    164

    Adapter paint

    serial # 2b090964

    Can i use a quick silver black primer to paint theadapter plate?
  23. Thread: Torque Values

    by josie201
    Replies
    12
    Views
    374

    Just to make sure, manual (90-8M0071433) list the...

    Just to make sure, manual (90-8M0071433) list the torque value on the powerhead nuts as (snug, 25lb-ft, then 50 lb-ft), this is the correct torque? Strainer hose, stat hoses, flush hose, and the...
  24. Thread: Torque Values

    by josie201
    Replies
    12
    Views
    374

    the 10 nuts holding the power head on. In a...

    the 10 nuts holding the power head on. In a somewhat related question, I need to replace the power head gasket when I replace the lower crankcase oil seal. This seal was replaced in 2018, assuming...
  25. Thread: Torque Values

    by josie201
    Replies
    12
    Views
    374

    Torque Values

    Serial # 2b090964

    tightening sequence and torque values (snug, 25lb-ft, 50lb-ft) listed correctly in my mercury service manual.

    thanks
Results 1 to 25 of 266
Page 1 of 11 1 2 3 4