Search:

Swapped an injector and coil from old Powerhead and ran the motor on muffs. Still somewhat hard to start but did seem to idle better. I dropped spark to cylinder 5 and the engine stumbled then picked...

All cylinders have right around 120psi during a compression test when motor was cold.

Pulled plugs after work today. These were new before running the motor yesterday on the lake. #5 plug has an oily residue when compared to the others. Bottom right in the pic. When I do the dynamic...

I've posted on the ETECownersgroup site as well. Haven't had much luck there.

Nothing shows up under EV Diag. I installed the gaskets that came with the new adapter plate and a new Powerhead base gasket. Everything looked correct based on how the old ones were. No passages...

Update, went to the lake again today and was messing around with stuff and noticed lack of exhaust coming out of the prop especially at idle. Brought it home and dropped the lower unit and didn't...

That's what I ended up doing. Rotating my oil tank and there was enough room. Cracked my oil filler hose so had to order some.

I was looking at a lot of motors after mine blew and saw a lot of them in that year and hour going for $5000-$7000.

Etec 250- E250DPLSOC

Put a used Powerhead on, along with a new adapter plate. Got everything hooked up and got it started on the muffs (hard to start, figured it was air in the fuel lines from...

Just adding another battery for electronics

Anyone willing to share what their bilge set up looks like with 4 batteries and the oil tank in there? Adding a 4th battery and wanting to clean up the bilge area while I'm in there moving stuff. Too...

Looking at upgrading my wife's vehicle. We're interested in a 2017 or newer Toyota 4runner. We have one child that is still in a car seat and maybe going to have another child at some point. Anyone...

Pulled my Powerhead last week and found a cracked adapter plate. Ordered a new one and started reassembling tonight. There is an extra hose barb on the starboard side of the adapter when I compared...

Separate Items, just switching some stuff out on the boat, upgraded a graph and got rid of the 360.

Gen 1 Helix 10 SI with side imaging transducer, rubber cover and cable management clip, will need gimbal mount and power cord. $650 TYD

Mega 360 with Ultrex mount, power cord has been spliced but...

I plasma cut the ring out of a piece of 1/2 steel and bought a lifting eye bolt off Amazon for $8 and lifted mine last Thursday. If you want I can cut one for you and mail it or send you the dxf file...

I'll take the lightly used one. Pm me your PayPal and I'll send payment

#4 cylinder leaned out. Willing to sell individual parts off it. No EMM or Starter. This was a replacement Powerhead from Evinrude after the original blew in 2017. $1500 plus shipping for the entire...

Thanks. I made one up based on the sticky one. Just cut some 1/2 steel plate in a circle with some slots and a hole in the middle for a lifting eye.

Going to be swapping powerheads next week, does anyone have the lift ring that would be willing to rent to me for a couple days then I ship back? I will cover costs. Evinrude part number 342672

Looking for a helix 10 gimbal bracket if anyone has one laying around.

Bought a used ETEC to swap with mine that blew in the fall. I currently have a 6" hydraulic jackplate and the sandwich style talon brackets. Brackets are between the motor and the jackplate. Each...

Sap is coming out around 2.5% sugar content which is 34:1. We use reverse osmosis to pull off more water. This last batch the sap coming out of the RO was at almost 10%. Hoping for another 30 gallons...

Did our first boil today and ended up with 9 1/2 gallons of syrup. A little less than we were expecting but we'll take it. Here are some random pics of the process.
543786
543787
543788
543789...

Lots of guys are running them in their ice shacks and for ice camping. Don't know much about them but look at some of the ice fishing forums for more info. Iceshanty.com indepthoutdoors.com and...