I am in need of some help with my 08 Skeeter ZX200 as the rear pedestal base is messed up and the post will not screw tight. I realize the nut is messed up underneath but unable to find a replacement...
Type: Posts; User: skeeterman70
I am in need of some help with my 08 Skeeter ZX200 as the rear pedestal base is messed up and the post will not screw tight. I realize the nut is messed up underneath but unable to find a replacement...
Thanks for all the help guys, I am getting out this week to run and test at different settings. I can get it to run good by myself but then when the boat is loaded with water and both tanks full with...
My mechanic put the jackplate and motor back in the same holes as the original setup. PTP was 4.0" before the old jackplate was replaced. I am at 8 dots on the jackplate as before.
There is a...
I have a 2008 ZX 200 with a HPDI 200 that required a replacement of my 12" jackplate due to one of the ears breaking. Had the same model Slidemaster manual jackplate installed and now the boat...
Are they sold as a set?
There is a prop service around Red Oak that I spoke to at the Bass n Saltwater Expo last year. I don't have the information with me but will look this evening.
Submitted my documentation on 4/19, processing since 6/6, and said I had to wait 12 weeks before ready to deliver but still nothing.
What pitch is the Braxo1 XS? I am interested if it will fit my boat.
I currently have a Tour Digital Motorguide 82 pound thrust trolling motor. The shaft is 1" diameter and the Lowrance Active Target bracket will bottom out the bolts, causing the mount to not be...
I have a new HDS 12 Live that starts emitting chirps and different noises from the unit. The unit works fine and has no issues but not sure what is causing the sounds...any ideas or should I call...
Did he release her? I can imagine it being hard to not get it mounted as that is a once in a lifetime trophy for the Roanoke River system!
Seems Plymouth was the spot for the majority of bites Friday...the river was high, muddy, and fast making the big bite hard.
I have a 2008 ZX 200 Skeeter bass boat and looking to find the raised dome Skeeter lettering. When can I find them as they are 3.5" in height and most places are 4".
Been running a Temptest 25p 3 blade prop on my 2008 ZX200 Skeeter with a 200 HPDI. 63mph @ 5600. PTP is 3.50", 40 gallons of gas, both livewells full, and 2 people. <br><br>Tried a Fury 24p 4 blade...
I have a 2008 ZX 200 and wondering if the newer year model cooler lids will fit and hold up better that sits between the seats. Found a replacement but wanted to see what you guys are using.
...
I have a 08 Skeeter ZX200 with a 200 HPDI. Currently running a 25P Tempest but wanting to go to a 4 blade prop and wondering if a Fury 4 or Bravo XS works better on these boats. Running 5700-5800 and...
When the motor is turning either by battery or hand I hear a loud scrubbing noise in the lower unit, could this be brushes wore out or armature magnet issues?
23 was 1st, 19 was 2nd, and BF was 5.81...a lot of 3lbers caught
The Wilson/Rocky Mount area was spared the full wrath of Flo. Some flooding in the Roanoke/Chowan/Albemarle Sound but not heard any reports of fish kills.
Two 27 pound bags caught and big fish was over 8...a lot of big bass caught in the all day rain event.
Fished a club tourney out of Plymouth Saturday, the Roanoke was high and flowing hard but the bass were biting!!! Caught three limits of keepers...
Dennis Pridgen and Al Lancaster won it...
I remember Jerry used to have holding tanks there at the ramp to put the fish in and recover. He would release them later that evening after the water and sediment had settled to give the bass a good...
Was in need of some advice as to which breaker I need for a Motorguide Tour 80 24 volt trolling motor. Do I need one for the positive and negative lead? I currently have the old resettable type on...
Water is still low, ramps not useable. You will have to back into the water off to the side of the ramp at Sapony Creek landing. They are catching some nice bass out there lately.