I have a 2006 Evinrude ETEC 225 HO gen 1. Which flo torque II hub kit do I need to run a tempest plus prop, part #8M0119081 or part #8M0107220? Currently I'm using #8M0119081, but I recently bought a...
Type: Posts; User: fish80
I have a 2006 Evinrude ETEC 225 HO gen 1. Which flo torque II hub kit do I need to run a tempest plus prop, part #8M0119081 or part #8M0107220? Currently I'm using #8M0119081, but I recently bought a...
Thanks Bighare2
I haven't paid attention to the idle rpm really but i think it does idle in neutral at about 500 rpm. Just noticing at WOT my graph is showing about 5800ish and my analog is showing almost 6500.
I have the engine data cable going from my ETEC to my lowrance graphs that show my rpm, trim %, load, voltage, etc. My problem is that the rpm's shown on my graph are about 400-500 lower than the...
I have the engine data cable going from my ETEC to my lowrance graphs that show my rpm, trim %, load, voltage, etc. My problem is that the rpm's shown on my graph are about 400-500 lower than the...
Boat: 2006 Z20
Motor: 2006 ETEC HO 225
Jackplate: 10" Slidemaster
Prop: 26P Tempest Plus, 3 large plugs
Prop to Pad: 4"
GPS Speed: 66 mph WOT, full tanks, medium load
Rpm: 5800
WP: 18 psi
Thanks
Does anyone happen to have a vented motor cover for an ETEC HO 225 or know any place that still makes them?
I have a Ghost trolling motor with the built in HDI transducer and a Gen 3 tough 9 with the 18.2 update. What setting do I need to use to read the HDI transducer to give me HDI/2D/water temp? I have...
Thank you for the help.
I have an HDS Gen 3 on my console and just recently got a structure scan 3d module. I have the graph wired straight to my battery with the red wire going thru a breaker and to the battery, and the...
Thank you for answering my questions. I was unsure because I have been told that the Gen 2 wouldn't work with the Ghost HDI transducer for 2D and DI. I was told that I would have to have at least a...
Will that allow me to see 2D and DI? Thanks
I was just wondering if the Lowrance Ghost's HDI transducer will work with a HDS 9 Gen II touch? Or is there an adapter cable that I will need? Thanks
I just rewired my electronics after I got a little advice from a expert in installations. I ran 10ga. wires directly from the battery through a on/off circuit breaker 50amp with a inline 5 amp fuse...
Mine was freezing after I updated to the 18.2. I reverted it back to the 7.0 update that I got from Bill and it has been working perfectly since.
Does your 2D freeze also?
Ok. Thank you Bill
Does anyone have the software update 7.0 for a HDS GEN3? The 18.2 update is causing me nothing but problems. Thanks
Thanks for letting me know the cost. I have a 06 Z20 and I plan on doing the same thing next spring. The upgrade looks fantastic by the way.
How much did the upgrade cost?
I have used slick mist for years and more recently marine slick mist.
I picked up a tool holder from procise outdoors and screwed it on the right side step up area. It’s works perfectly. As far as the bump board holder, I’ve been waiting on the same question.
I can...
The motor was fully serviced this spring and compression and all was good. I'm going to do some asking around and see if I can get my hands on a few fury and or tempest props to try. I will set my...
I've had a lot of pie lately but I hope I haven't gained 1000 lbs. Haha. When I bought the boat it had the lightning gears and ran in the low 70 range. A little grumpy log caused me to switch lowers....