Search:

Type: Posts; User: rojoguio

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    426

    If you were closer I would give it to you. You...

    If you were closer I would give it to you. You won't need much. Be sure to bury your flake well, if it is colored and you sand the color off all flake is silver under the color treatment to the flake.
  2. Replies
    18
    Views
    426

    Video explains a lot. I'm with APS that it still...

    Video explains a lot. I'm with APS that it still must be very thin to spray out of a can. The salesman doesn't say anything about a flake job just that they have a very library if color formulas.
  3. Replies
    18
    Views
    426

    Another point I should have made earlier is any...

    Another point I should have made earlier is any professional repair later you will have to grind out the contamination you add. I looked at the link but I see no tech sheets or info. Isocyanate is...
  4. Replies
    18
    Views
    426

    Just keep in mind anything non-catalyzed you put...

    Just keep in mind anything non-catalyzed you put on your boat will wrinkle and lift later including gelcoat.
  5. Replies
    18
    Views
    426

    Paul he doesn't mix the flake, you spray down a...

    Paul he doesn't mix the flake, you spray down a wet coat of clear then apply the flake with a dry flake gun. That is what I have here. After applying the flake clean compressed, air regulated down,...
  6. So if you have spots that won't seem to go away...

    So if you have spots that won't seem to go away there is a bacteria that eats the pigment in vinyl. It leaving white vinyl pink. If that is the cause of the damage there is no fixing. Now it does not...
  7. Replies
    18
    Views
    426

    Rattle can clear not only won't build enough to...

    Rattle can clear not only won't build enough to bury the flake but will peel off. Not a great idea Bud. A high solids Euro Clear will stick if enough tooth is left after sanding. No 800 grit stuff I...
  8. Replies
    15
    Views
    560

    You must use a adhesive remover. I have posted...

    You must use a adhesive remover. I have posted here a few times already. Search my posts with adhesive remover and you will find it. Adhesive remover breaks down the adhesive to components and takes...
  9. All the caps I have pulled the cap is bonded to...

    All the caps I have pulled the cap is bonded to the hull at the transom. I have never had to cut it free since the bond has been more of a thickened resin filler with poor adhesion but I did do a lot...
  10. Replies
    2
    Views
    245

    Bud, thank you for the vote of confidence, here...

    Bud, thank you for the vote of confidence, here is the link to my Champion, I will be back on it this summer.
    https://www.bbcboards.net/showthread.php?t=934664&highlight=171sc
    It has pictures of...
  11. I spray with a 2.6 HVLP Gravity feed. I had a...

    I spray with a 2.6 HVLP Gravity feed. I had a nice talk with the owner once. He said their thinner is best to maintain the same spray gloss so now I pile it on then sand flat then come back and spray...
  12. It's new packaging for me, better than the gallon...

    It's new packaging for me, better than the gallon paint cans it used to come in.
  13. I do not do any gelcoat work without it.

    I do not do any gelcoat work without it.
  14. Replies
    7
    Views
    640

    That's why I run custom windshields on...

    That's why I run custom windshields on everything. I may have some wind drag but my hands and face are protected as winter fishing is the bomb for me.
  15. Replies
    3
    Views
    500

    #1 Coosa Bluewater 26, also #2, #3, #4, & #5. 5...

    #1 Coosa Bluewater 26, also #2, #3, #4, & #5. 5 of the best reasons. I did it professionally, all I ever used was Coosa Composites. All the shops thru the region here use Coosa Bluewater 26 too.
  16. First, closed cell needs to lay flat. I don't...

    First, closed cell needs to lay flat. I don't know your boat but in most carpeted cockpits the carpet hides the nasty seam between the Cap and the hull. It is not finished, they carpet over to hide...
  17. Replies
    3
    Views
    470

    I replaced transoms for a living. Only used Coosa...

    I replaced transoms for a living. Only used Coosa Bluewater 26. Search my posts bud concerning a pourable transom and my explanation of why doing it right matters long term. My SD-80 is a '87 so...
  18. Replies
    3
    Views
    470

    Bud pulling the cap is fairly straight forward....

    Bud pulling the cap is fairly straight forward. If you take pictures on the inside around the splash well, cockpit, front storage we might can help you. A year model would help too. I have a SD-80...
  19. Replies
    348
    Views
    44,808

    Just a quick post with the rod holder installed....

    Just a quick post with the rod holder installed.

    533117
  20. Replies
    13
    Views
    915

    I forgot to post for you a 2003 Triton in my shop...

    I forgot to post for you a 2003 Triton in my shop now for some repairs. New 300HP (90 days old), I recently completely reworked the canvas, that is the second T-Top the first one cracked almost...
  21. Replies
    348
    Views
    44,808

    Well I finished welding, sanded, and Painted the...

    Well I finished welding, sanded, and Painted the Rod holder today. It will be installed in the morning.

    533079533080533081
  22. Replies
    13
    Views
    915

    Very Respectfully speaking, I would not touch it...

    Very Respectfully speaking, I would not touch it for $4500. That is a great price if they do it right. Price a replacement boat without any issues. So if I can provide some perspective, I would...
  23. Replies
    13
    Views
    915

    John, I hate to be the first to tell you this but...

    John, I hate to be the first to tell you this but if you like the boat bring it to a professional. All that gelcoat must be removed and a tooth applied to the substrate then new gelcoat with...
  24. Replies
    348
    Views
    44,808

    I'm going to get to the Arch / Bimini Top but so...

    I'm going to get to the Arch / Bimini Top but so many other things keep getting in the way like the Crappie are on Fire. Hard to ignore them.

    533005533006
  25. Replies
    348
    Views
    44,808

    Unique Rod and New Net Holder was Needed

    The Flounder run is on top of us and I need the little boat to run the lower deltas so I can fish for trophy Flatties. Also we can catch Bass, Crappie, Flounder, Redfish, Speckled Trout all in the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4