around 80 degrees the wifes top comes off....
Type: Posts; User: Gatchmo5710
around 80 degrees the wifes top comes off....
After putting 400 hours on my G1 Etec i will be purchasing another Etec if mine ever fails.
Verify your motor height is correct, or close... step down to a 23 pitch.
Is your engine still healthy? Compression good?
If you listen closely you ca hear his wife yelling "I said reverse"!!!!!!!!!!!!!!
896 DC
FYI im currently testing some props and height and will report once i have better info.
UPDATE: Bought a cheap 19pitch 4 blade solas aluminum to see how it would feel....
14.25x19 5500 rpm max at 50 MPH. Hole shot loaded was too slow at 3300 RPM, light load was barely acceptable...
Yes it should. As long as your have the pressure sending unit installed and the EMM setting turned on.
I use my lawn tractor for all my trailers. Turns very sharp and it even cuts the lawn.
I can get either of these right now for a great deal... if you think they would fit the bill?
Rebel TBX 15 1/2” x 17
Cyclone Prop 14 1/8 x 19 #763942 I worry i wont have the RPMs with this...
Speed is not a concern. This is the family work horse so cruising and hole shot are priorities...
Mike what 4 blade would you recommend? Pitch?
JR19 yes your correct. Ive reached my limit or more with the 17 pitch. Too close on the 19... I can tell the engine is reducing i RPMs when i max her out. But know i back her off quickly. Im hoping...
Update: mounted jackplate. 3.5 inches P2P.
17 pitch- 6250 RPMS at 51. 19 Pitch 6100 RPMS at 51. Good water pressure. Better handling across the board. Good lift. Same hole shot at 3800 and 3400...
I just broke 300Hrs on the 2011 G1 v6 150. Absolutely love it. Im coming from a old 89 E200. This 150 is quite impressive. Torque, fuel efficiency, and quietness have blown my mind. I really cant...
Finally bit the bullet on a 6 inch jackplate to help dial my boat in further.
Currently have cheap Evinrude aluminum 17 pitch turning 6100 at 51-54 mph. 19 pitch turning 5900 at 52-56 mph. Roughly...
I cant believe the amount of people on here that would carry a loan for 30 years!! SIMPLE math shows that paying a little extra each month way out weighs the benefits of refinancing. You saved 200$ a...
Whats your temps when idling? I have a 150 G1 that spends 4 hours plus each outing idling(trolling). Plugs look almost new at about 50-75 hrs when i change them out... though i try and get a hard run...
No expert but it looks as though injector wasnt seated properly allowing combustion gases to escape. Or the injector itself was leaking.... either way perform a compression test, test or replace...
Generally you dont save much unless you do the work yourself... and the definition of a rebuild is debatable. One guys bores over .030 and puts pistons in and calls it a repower. Another guy starts...
My boat is used as a tool. And i treat it like one. Repowered my 99 nitro with a 150 etec. Abuse her like a old girl, runs like a fresh pup. Best for me as i laugh watching the guys make their...
Sounds like a powerpack.
99 896 DC. More prone to porposing than others but you can learn to drive it. Ive been recommended a hydro foil, shifting weight, jack plate with correct prop... all im sure would help most...
Imagine being so dominant in a league that when you make the playoffs people say the dynasty is over. Another year will come and go, another 10 win plus season, another playoff run... im just proud...
Beat the ice on Otter Creek, barely.... probably the last boat out this year. Trolled swimbaits and rattle traps. Caught 10 or so including this pig.
388707
388711
388710
Then i went further...
Water pump kit, thermostat, ECM updates, exhaust nipple, spark plugs, fuel filter, gear oil change, anodes, re-grease, maybe a few other small things. Kits about 350$. Labor another 200? I do it bi...
Yes, ive seen all sorts of switches, solenoids, relays, etc wear out do to age/corrosion/burnt contact points. If im troubleshooting a electrical problem like yours i usually do all wiring,...