Oak ridge and Fisherman's one stop
Type: Posts; User: gofish5252
Oak ridge and Fisherman's one stop
Danny Arnett Lake fork Boat carpet. Good Guy.
I just put the 52 inch Ultrex on my Tr20.
i have no problem with the rod locker lid.
I used poly cutting board to raise mount
over bow shroud. wraped the cutting board
with vinyl black tape...
I have a 03 tr20 with a Merc 225 efi. Would run 78 to 79 with a 27 Tempest. Now with 10 foot blades, 36v Ultrex best I can get is 74 with light load. Slow out of the hole now, worked 25 Tempest....
Beautiful rig
Would love to see one. Might make me sell my triton.
What kind of gauges are those? Looks good. I need to replace mine.
I have a 03 tr20 with Merc. 225 efi would run 79 with 27 tempest. Added 2 10f blades and a extra battery for 36v troller. Killed the hole shot and speed down to 73. Played with Jack plate and just...
Warranty information is avalable in many different forms.
The TSB is intended to assist the tech to repairing a symptom.
This system is in place to help the customer, dealer, tech, and manufacture....
03 tr20 no stress cracking, fish lake fork every week end.
Never have had a problem. Would love to have a new boat. But this one has been good to me. Can't let her go.
Tach. May not be reading correct. But the loss in speed
Has me dumb founded.
Data is correct on gps. I have owned this boat sense it was new. No one ever believes the numbers until they have been it. Nothing else has changed.
I have the stock 6" plate. I put the plugs out of precaution
When I got the new prop in October, the water pressure went down. Put the plugs in and pressure went back up. I was running a 27 trophy...
Engine is a 2003 and tag on engine says max RPM is 5900. It does have low water intake. Plugged the top holes due to suckling air at speed.
Rev limiter buzzer is at 5900. Yea I don't get it at all. I will try to bring the engine up some more. I do have the 3 top holes plugged.
I just put 10 foot blades on my Tr20 with a 3l 225 efi merc and have lost about 9mph of the big end. I run a worked 26 tempest that was on the revlimiter at 78 mph. Knowing I was putting poles on I...
I did check nuts and bolts. No problem there. I thank the spike may be bent or the pivot knuckle has a problem. Going to call PP Monday.
I have 2 new 10 foot blades. I am having a problem with the starboard side not seating in place when in full up. The arms are fully up but the spike sticks out and moves around when on pad. No...
Engine is to high. To high equals no leverage to lift the transom
I have a 03 Tr20 with a 225 efi. I spin a worked 27p trophy 2 to
5800 rpm at 77mph. 2 1/4 below pad. Tuck it under Hamer the
Throttle. If you are plowing with the nose up something is not
Right....
Sweet ride. Im jealous.
Ok was just trying to get a basic ballpark figure to get an idea of what I would be spending.
3.0l 225 efi serial number OT737370. I have a few things that need to be done. My pivot shaft bushings needs to be replaced and I need to have exhaust tuner cleaned. I was thanking since the power...
Possibly the stator on the Yami has a draw causing battery drain. Disconnect battery + to engine and simulate on water condition ie graphs and pumps running. Check battery voltage after your 4 hrs...
Keep me in mind. Looking for a center seat bottom. May be looking for other idems