Sold mine a couple weeks ago. Mine had Yamaha & swing away tongue, it measured 23'-3". That is with the motor straight. Yams are a bit longer. You could pick up a couple with motor turned.
Type: Posts; User: ShaftDilbert
Sold mine a couple weeks ago. Mine had Yamaha & swing away tongue, it measured 23'-3". That is with the motor straight. Yams are a bit longer. You could pick up a couple with motor turned.
I just listed it in the props for sale section with pics.
See IM.
I have had numerous Fury's. i put additional holes in it, and yes you can miss the rib on the one that is near it. All mine have been B&B. big dif in lift if done right, which is not easy.oh the...
Well i sold my boat today, my 07 alpha 199dcx with a 08 Yamaha 225 SII. I watched the new owner drive it off. Best boat and motor i have had. I have had a bass boat for 30 of the last 35 years. I...
Here is one, it is listed here as well. any questions let me know.
Legend Bass Boat Alpha 199 DCX
Also a not here on my 199..
I just sent Al the listing so it should be posted in a few days. Thanks for the input.
Steven
I will be listing my 199 for sale on the boards here in the next week or two. Before i do i would like to get your thoughts on an appropriate asking and selling price. The market is what it is.. If...
I recently replaced my rear axle and in the process went through that. You want to fill it up all the way. There is a small "groove" near the top. I filled to that level with lucas hub oil and have...
New rear axle is in. Not a very complicated job just very time consuming and messy doing it by yourself and with the boat still on the trailer. Hardest part was removing the caliper bolts. Port side...
I am in the same boat (pun intended). I have tried numerous brands, some gave me a headache and others the readers were not positioned well for me. I have a pair of ONOS that are great, good quality...
Well, i got sort of lucky/unlucky. Took the wheel off and inspected. Oil was leaking because the fill plug was about to come out. That is the lucky part. The bad part is that the axle spindle is...
It must be on really good. Myself i'm not much for prying as i have seen someone break the gearcase doing it. One more suggestion.. Get a piece of black pipe that will fit over your prop shaft. Get...
I have an early SII 225 manuf in 5/07. Mine has always been that way for the first start of the day. When new i brought it in numerous times for it to no avail. I have over 300 trouble free hours on...
I have run the 25 and 27 T1 and now have a 25 solas scorpion. The scorpion runs between the two in rpm's. They run stiff like a Fury. It has a ton of lift and performs better on my rig than either...
Yes you do need to change it, it should be in your kit. Takes an extra 5 seconds to change unless yours is stuck, in which case hit the thrust washer with a punch near to the center of the shaft a...
Thank you all for the information..
Steven
Who is a board sponser that sells UFP parts? My ezloader is 6 years old and one of the hubs is leaking oil. This is the first problem i have ever had with it. Would like to replace entire hub...
I have an 08 225 SII. Changed the filter inside the vst today at 309 hours. Have to say i appreciate all the posts on how to do routine things on these motors. The filter on mine was virtually...
Oops wrong forum...
They all break, some more..much more, than others. NOT and that is from first hand experience.
I run 2 LMF 400's and 4 LMF 200's since 06. Mine are a combination of both blue and red. Never have updated or had any software issues. Have however needed to replace one lmf 400 and two of the 200's...
Dennis S is correct. I changed mine out about a year ago, they are cheap. Suggest getting an extra, i destroyed one getting iit to line up right before tapping in the pin.
Sniper14 lb here and never an issue. Best fc for me.