Search:

Type: Posts; User: wmitch2

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    1
    Views
    1

    I've heard you can replace the whole relay setup...

    I've heard you can replace the whole relay setup with a $20 Wench relay from Am....... !
  2. Replies
    6
    Views
    348

    Bradrodfish where are you ???

    Bradrodfish where are you ???
  3. Thread: Breaker Issue?

    by wmitch2
    Replies
    2
    Views
    87

    Sounds like a bad or weak breaker. I'd start...

    Sounds like a bad or weak breaker. I'd start first with checking all the connections. Make sure they are all clean and tight. Then replace the breaker if it still does it.
  4. Replies
    2
    Views
    75

    UHD 93ev transducer question

    I have 2 UHD 93sv units at the bow. One is for Live Scope and the other is for Chirp/Down/Side scan. Is there a Y-Cable that will allow me to use both units off of one GT56 transducer ??
  5. Replies
    48
    Views
    3,231

    I found this on Am....... over the trolling motor...

    I found this on Am....... over the trolling motor peddle, high rise and two graphs. Strong and stable in all weather. If I'm gonna make a long run, I can remove the Garmins from the cradles and...
  6. Replies
    9
    Views
    422

    I had a similar issue only mine was wearing on...

    I had a similar issue only mine was wearing on the inside of the tire. I pulled the wheel and noted that the splined end holding the hub to the torsion arm was not "Flat" in the arm mount. I...
  7. Replies
    2
    Views
    158

    It has to be deployed to work !

    It has to be deployed to work !
  8. Replies
    6
    Views
    123

    I've always used a "Snake" of Plumbers Putty and...

    I've always used a "Snake" of Plumbers Putty and make it just a little larger than the transducer. Holds the epoxy and is easy to remove after use,
  9. Replies
    33
    Views
    659

    Not sure, that's just what my mechanic called it....

    Not sure, that's just what my mechanic called it. I'd have it checked before just changing it, it was like $400, so You do need to have it troubleshooted by a qualified service tech.
  10. [QUOTE=Rick H;13456383]To each their own but I...

    [QUOTE=Rick H;13456383]To each their own but I hate black wheels. :wink:

    YEP !! I agree 100% !! Especially since my favorite color is CHROME !!!
  11. Replies
    6
    Views
    318

    It may be different for the brand of tire, how...

    It may be different for the brand of tire, how many plies, etc. It will be printed on the side of the tire as to what #s for that particular tire. The max #'s already accounts for expansion.
  12. Thread: Medical Test

    by wmitch2
    Replies
    1
    Views
    463

    Medical Test

    HHHHUUUUUUUHHHHHH !!!
  13. Thread: Aluminum angle

    by wmitch2
    Replies
    16
    Views
    1,037

    They stay pretty much, depending on how rough and...

    They stay pretty much, depending on how rough and on how full the locker is. When they hang without hitting anything they pretty much stay put.
  14. Replies
    33
    Views
    659

    Mine was doing the same thing. Found it was the...

    Mine was doing the same thing. Found it was the secondary fuel pump. Replace it and all is good
  15. Thread: Length

    by wmitch2
    Replies
    2
    Views
    210

    My 2002, 205vx, 225 Optimax, 6" Jack Plate, 2...

    My 2002, 205vx, 225 Optimax, 6" Jack Plate, 2 axle, Tongue folded, Motor down is 24' 2". I don't think a single axle is any shorter. My garage is 25' deep and it fits no problem.
  16. Thread: Aluminum angle

    by wmitch2
    Replies
    16
    Views
    1,037

    I made my own with some 3/4"x3/4" Aluminum angle...

    I made my own with some 3/4"x3/4" Aluminum angle from Home Depot. Just drilled the holes 1/2" apart. Works great !!
  17. Replies
    15
    Views
    724

    Many confuse Flippin' with Pitchin'. Flippin' is...

    Many confuse Flippin' with Pitchin'. Flippin' is done with a length of line that doesn't change in the presentation to the target, Pitchin' is done letting line out as the lure goes out to extend...
  18. I have been thoroughly happy with mine !! They...

    I have been thoroughly happy with mine !! They work as intended !! I chose to use Pop Rivets instead of the Bolts that come with it. Just liked the look better.
  19. Replies
    15
    Views
    699

    I've used Emory Cloth or a medium Steel Wool to...

    I've used Emory Cloth or a medium Steel Wool to make it look better. The plastic outer shell is just a covering for the Transducer. As long as the plastic isn't cracked or broken you're good to go...
  20. Funds sent

    Funds sent
  21. ^^^^^^^^This one !!!

    ^^^^^^^^This one !!!
  22. Replies
    5
    Views
    361

    I added a fuse block in the front starboard...

    I added a fuse block in the front starboard locker for my graphs and connected a Perko cut off switch for the GLS10 box on the wall towards the console.
  23. Ill take these, send me your PayPal.

    Ill take these, send me your PayPal.
  24. Replies
    1
    Views
    58

    FOUND ONE, PLEASE DELETE

    FOUND ONE, PLEASE DELETE
  25. Replies
    12
    Views
    326

    I'd run it to the TM Skag. We used to do that...

    I'd run it to the TM Skag. We used to do that yrs ago to eliminate the interference.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4