Search:

Type: Posts; User: Used2fish

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Help with finding a few parts for older control

    2000 model 200hp johnson

    441910

    I've looked through some parts diagrams but cannot find the few parts that are needed to finish off the controls.

    Any help?
  2. Replies
    2
    Views
    479

    No sir. Looking through their website I found...

    No sir.

    Looking through their website I found a pic someone posted and it was a 202zx. I emailed them and asked what seats those were they sent me a link. I then replied and asked if they could...
  3. Sacrificial anode is done. Pulled the shaft...

    Sacrificial anode is done.

    Pulled the shaft by taking 2 2x4s about 3 feet long sandwiching the shaft running some long screws both ways through the 2xs then two little bottle jacks, one on either...
  4. The shift rod has an offset in the end. Does the...

    The shift rod has an offset in the end. Does the position of that offset not matter just the measurement?

    Thanks for help sir.
  5. Sacrificial anode?

    Sacrificial anode?
  6. 2000 johnson sei sterndrive shaft removal and replacement

    Guys I bought an sei stern drive lower unit and it ships without shaft and shiftshaft.

    Does anyone know of an instructional video on how to remove the old shafts?

    Is it possible for a half...
  7. Replies
    2
    Views
    479

    Seat replacement

    Hey guys several years ago I bought some seats for my 2000 202zx from bassboatseat. They did not fit well and the back deck compartments hit the seats when you try to open them.

    I know I must...
  8. Replies
    2
    Views
    218

    My buddy runs a 98 great boat. His 150 is carbed...

    My buddy runs a 98 great boat. His 150 is carbed and man I can't think of a more dependable motor than his.
  9. Replies
    23
    Views
    641

    That's likely what I'm missing. I'll do some...

    That's likely what I'm missing. I'll do some googling. Thanks sir you're help has been greatly appreciated
  10. Replies
    23
    Views
    641

    So unlike my Yamaha horn doesn't alert me when my...

    So unlike my Yamaha horn doesn't alert me when my lanyard is not attached to the kill switch?

    Either way the horn does not chirp when I put key into the on position either.
  11. Replies
    23
    Views
    641

    Back to the kill switch. The horn works (if given...

    Back to the kill switch. The horn works (if given 12 volts) I tested the voltage of the wires coming off the back of the kill switch and the contact is making and breaking with instillation and...
  12. Thread: 2000 ZX202

    by Used2fish
    Replies
    5
    Views
    481

    Taking the dimensions of them they do not sell...

    Taking the dimensions of them they do not sell them anywhere I can find I've gone from online retailers to trailer dealers.

    Skeeter dealer said they can get 1 from ezloader for 250. I've decided...
  13. Thread: 2000 ZX202

    by Used2fish
    Replies
    5
    Views
    481

    2000 ZX202

    Looking for a couple things and some info.

    I repowered this boat with a Johnson that came off a ranger. Real close to having it rigged and ready to go. The motor came with a 4 blade prop I'm...
  14. Replies
    23
    Views
    641

    I decided to delete the oil injection and premix...

    I decided to delete the oil injection and premix my oil.

    Mix ratio is 50 to 1 correct?
    Where is a good place to keep an eye out for a lower unit for that motor?
  15. Replies
    23
    Views
    641

    Keep learning new things daily. Sure enough it's...

    Keep learning new things daily. Sure enough it's carbed. I think I knew that a few years ago when I purchased it but I'd forgotten and started to believe it was injected recently. Glad it's not.
  16. Replies
    23
    Views
    641

    What's the overall opinion of the 2000 Johnson...

    What's the overall opinion of the 2000 Johnson with the Fitch injection system?
  17. Replies
    23
    Views
    641

    I got it. I feel like a genius. No actually I...

    I got it. I feel like a genius. No actually I feel dumb that it took that long.

    One thing. I'm still not getting any key Tone even though the key is in on position or if I remove the kill switch.
  18. Replies
    23
    Views
    641

    Getting somewhere. I kept the key turned and...

    Getting somewhere.

    I kept the key turned and moved the throttle handle and got it to turn over.
    350744350745

    The 1st pic with the throttle up and down where I assumed nuetral to be. The...
  19. Replies
    23
    Views
    641

    Just remembered that's the one going g to my oil...

    Just remembered that's the one going g to my oil tank which i opted to pre Mix so I deleted that tank.
  20. Replies
    23
    Views
    641

    I went through and checked all the plugs through...

    I went through and checked all the plugs through the harness made sure they are good and tight. Only plug on the motor that does not have anything going to it is this one.

    350742
  21. Replies
    23
    Views
    641

    Fuse is good.

    Fuse is good.
  22. Replies
    23
    Views
    641

    Can you tell me exactly where the 20 amp fuse is?...

    Can you tell me exactly where the 20 amp fuse is? I've looked and looked I a few modules cannot seem to find a fuse I remember the one on my Yamaha was very obvious.
  23. Replies
    23
    Views
    641

    Yes I installed shift cables and wiring harness. ...

    Yes I installed shift cables and wiring harness.
    No I've not replaced any gauges.
  24. Replies
    23
    Views
    641

    Omc control box? I did not install new gauges so...

    Omc control box? I did not install new gauges so I've got a plethora of plugs at the console not in use. I did install the throttle handle deal? Is that the omc control box?
  25. Replies
    23
    Views
    641

    350607

    350607
Results 1 to 25 of 26
Page 1 of 2 1 2