Search:

Type: Posts; User: willymac

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    273

    Finally a real review on the question asked...I...

    Finally a real review on the question asked...I decided to order it anyways based on their reputation. It shows up tomorrow.
  2. Replies
    0
    Views
    89

    Fury 3 25p for trade

    8/10 Fury 3 25p. Repaired and blueprinted by local prop shop, Propworx, had a slightly bent ear. Used for two years after repair with no issues. Repowered to 4 stroke and now too big. No hub...
  3. Replies
    6
    Views
    273

    From what I understand, dd26 is just rebranded...

    From what I understand, dd26 is just rebranded tuffskinz. Only tuffskinz has an option for the oil access door flap secured with velcro. I've already ordered one so I guess I'll find out on a few...
  4. Replies
    10
    Views
    360

    If you don't clean your motor before you put a...

    If you don't clean your motor before you put a cover on, I could see where it might. But the one I had on my 2 stroke for 5 years have no scuffs or scratches.
  5. Replies
    10
    Views
    360

    That's what I figured.

    That's what I figured.
  6. Replies
    10
    Views
    360

    Tuffskinz Mercury V8 ProXS vented cover

    I have this posted in the Merc 4 stroke forum, but I figured it would get more traffic here.

    Who has any experience with this cover with the velcro oil door access flap option? I'm wanting to...
  7. Replies
    6
    Views
    273

    Tuffskinz V8 vented cover

    I'm looking to see if anyone has any experience with the velcro oil access panel option on the Tuffskinz vented motor cover. I'm looking to see if it affects the integrity or fitment at all, or if...
  8. Replies
    20
    Views
    749

    No I do understand the importance of it. I guess...

    No I do understand the importance of it. I guess I'm just venting more than anything, especially since it has been confirmed that it is normal behavior of the system. I'll just have to deal with it.
  9. Replies
    20
    Views
    749

    I understand how I blew the fuse, question was,...

    I understand how I blew the fuse, question was, is that normal, and you answered my question that it is.

    My concern is, I like to completely disconnect power on my boat while in tow and storage...
  10. Replies
    20
    Views
    749

    Key off, battery cutoff off, 14 pin at rear of...

    Key off, battery cutoff off, 14 pin at rear of engine disconnected, and clean power fuse removed - no solenoid click when pushing engine mounted trim switches, replaced fuse only from above, faint...
  11. Replies
    20
    Views
    749

    Sorry, I edited my post. The second test was...

    Sorry, I edited my post. The second test was with 14 pin at motor disconnected.
  12. Replies
    20
    Views
    749

    Key off, battery cutoff switch off - clean power...

    Key off, battery cutoff switch off - clean power fuse blew when trying to operate engine mounted trim.

    Key off, battery cutoff switch off, 14 pin disconnected at back of motor- clean power fuse...
  13. Replies
    20
    Views
    749

    Mercury clean power question

    3B460301 250 ProXS

    My clean power is connected directly to battery. My engine is connected through a cutoff switch. When switch is in off position, if the key is turned on or trim switch is...
  14. I would stay at Fin and Feather. Good cabins,...

    I would stay at Fin and Feather. Good cabins, good restaurant on site, good part of lake. They have boat slips for rent and two launches, only one is wind protected. 40 minute drive to umphrey and...
  15. Replies
    29
    Views
    1,283

    Impact driver is for screws, impact wrench is...

    Impact driver is for screws, impact wrench is what you want. 3/8 dewalt is what I use and can normally break the lug nuts loose.
  16. Replies
    6
    Views
    722

    I had a 2012 H18 with F115 and 6 inch manual...

    I had a 2012 H18 with F115 and 6 inch manual plate. I ran a Yamaha K21 prop and was able to see 52-54mph regularly. I don't remember any other details on the setup.

    I'm not exactly sure what the...
  17. Replies
    13
    Views
    1,049

    Try etsy.com

    Try etsy.com
  18. Replies
    19
    Views
    1,417

    Next time you are in rough water and running...

    Next time you are in rough water and running hard, look back at your motor and see how much it moves.
  19. Replies
    224
    Views
    10,046

    Its not, but why wouldn't workers strive to make...

    Its not, but why wouldn't workers strive to make a living wage from a company that is very successful. The salaries of these employees being a little higher wouldn't put a strain on Amazon. The...
  20. Replies
    224
    Views
    10,046

    Whats wrong with wanting a stable schedule,...

    Whats wrong with wanting a stable schedule, decent wages that you can make a living off of, and benefits? Not everyone is going to be a CEO or boss. Most people, that are in the upper management...
  21. Replies
    26
    Views
    1,892

    H2O branded crankbaits are not bad, especially...

    H2O branded crankbaits are not bad, especially for the price.
  22. Replies
    16
    Views
    1,613

    While yellow tape is suitable for fuel lines,...

    While yellow tape is suitable for fuel lines, white is also suitable. Yellow is double density and marked yellow for gas lines where double density is code required (methane, propane, etc., not...
  23. Replies
    16
    Views
    1,613

    Ptfe tape is compatible with gasoline. Always...

    Ptfe tape is compatible with gasoline. Always make sure that leading first thread does not have tape on it so you never have to worry about it breaking off and ending up in fuel system.
  24. Replies
    18
    Views
    1,165

    Insurance agreed to replace case without much of...

    Insurance agreed to replace case without much of an argument. Just got payment and hopefully parts aren't on national back order.
  25. Replies
    18
    Views
    1,165

    Insurance states that they have to repair/weld...

    Insurance states that they have to repair/weld the skeg back. I'm trying to push it up the ladder to get a new case. I'm going to call them back tomorrow and argue some more.
Results 1 to 25 of 210
Page 1 of 9 1 2 3 4