Search:

Type: Posts; User: omcforever

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    7
    Views
    80

    A good used or rebuilt unit usually will run you...

    A good used or rebuilt unit usually will run you $300-$400
    New units retail o $1186.99
  2. Replies
    7
    Views
    80

    Don't know how you are doing your search's (part...

    Don't know how you are doing your search's (part number only maybe) but I found them from $275-$800. Try looking for just 40hp omc/J/E tilt assemblies.
  3. Replies
    7
    Views
    80

    Ebay is your friend.

    Ebay is your friend.
  4. Replies
    3
    Views
    157

    :thumb up2:

    :thumb up2:
  5. Flywheel does have to come off and recommend link...

    Flywheel does have to come off and recommend link and sync per your OMC manual to re-verify timing(have seen it change a few degrees after flywheel is removed and re-installed). Insure you have no...
  6. CDI is junk. Went thru so many CDI coils and...

    CDI is junk. Went thru so many CDI coils and stators and pick ups that where new and failed or bad from the box.
  7. Guys,,this a 13 year old thread.....every symptom...

    Guys,,this a 13 year old thread.....every symptom doesn't always have the same culprit.
  8. 13 year old post..member hasnt been active since...

    13 year old post..member hasnt been active since 2014. Just start a new post explaining your issue in depth.
  9. Replies
    42
    Views
    1,875

    Not a bummer...actually good to fish for fun time...

    Not a bummer...actually good to fish for fun time to time to re-set.:thumb up2:
  10. Replies
    16
    Views
    303

    If you are going to do it yourself, invest in a...

    If you are going to do it yourself, invest in a real OMC service and repair manual for your setup. Saves $$$$ and you learn about your motor. Check all connections/connectors, ect first. Check...
  11. Replies
    16
    Views
    303

    I would get a new "guy" first.:smile:

    I would get a new "guy" first.:smile:
  12. Again,,find out why your tach doesnt work.:thumb...

    Again,,find out why your tach doesnt work.:thumb up2:
  13. Replies
    3
    Views
    174

    If it is really bad/bare aluminum,,,I use zinc...

    If it is really bad/bare aluminum,,,I use zinc chromate on the bare areas before applying the top coat.
  14. Replies
    16
    Views
    1,506

    And I really found this amusing----- "Im not...

    And I really found this amusing-----

    "Im not gonna have the boat long but im sure i can still get it to pass 60mph without fixing the RPM tach. Probly will fix it anyways. I have to get my prop...
  15. Replies
    16
    Views
    1,506

    Yous ask for help here and get advice then dont...

    Yous ask for help here and get advice then dont reply or follow and ask the same questions in the Ranger forum,,,and get the same answers......Geez.:doh:
  16. Maybe not.....THAT/THIS could be indicative of...

    Maybe not.....THAT/THIS could be indicative of your issue!!!!! Bad electronics-stator-regulator could cause running issues. FIND OUT WHY THE TACH ISNT WORKING FIRST. Also like asked in the OMC forum,...
  17. These questions/comments where made in the OMC...

    These questions/comments where made in the OMC forum- Fix the tach/a non working tach could indicate motor electronic issues that could hurt performance. Since you didnt mention you just got the...
  18. Replies
    16
    Views
    1,506

    A non-working tach could be an indication of...

    A non-working tach could be an indication of larger issues that could cause performance issues...get that motor checked out.
  19. Replies
    16
    Views
    1,506

    It is useless to mess with the jackplate until...

    It is useless to mess with the jackplate until you have a working tach and know all is in harmony with the motor. Was the speed on the dash speedo or GPS? If the prop needs re-done, do it but please...
  20. Replies
    2
    Views
    91

    Why not post your problem here so all can...

    Why not post your problem here so all can learn,,,,,,OMC repairs and advice is not usually done via PM's.
  21. Replies
    16
    Views
    1,506

    this is an old thread,,,,Have someone check your...

    this is an old thread,,,,Have someone check your motor out to insure it is running up to par and nothing is amiss/out of adjustment before you go throwing props at it. How long you owned the boat?...
  22. Replies
    24
    Views
    379

    "High performance 150 HP engines and any engine...

    "High performance 150 HP engines and any engine using a 4-3/4″ gear-case such as Command Thrust MUST use SeaStar." and a true GT/XP 150 are a high performance engine on a heavy boat. But again, your...
  23. Replies
    24
    Views
    379

    Your money and boat. Good luck. Just trying to...

    Your money and boat. Good luck. Just trying to interject real world experiences and failures with the Baystar.:thumb up2:(and I own torque wrench),,,:roll:
  24. Replies
    118
    Views
    2,980

    :thumb up2:

    :thumb up2:
  25. Replies
    118
    Views
    2,980

    :thumb up2:

    :thumb up2:
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4