Don’t know about the telltale nobody looked at it we were trying to get back to the trailer
Type: Posts; User: machinist
Don’t know about the telltale nobody looked at it we were trying to get back to the trailer
We got an overheat alarm and it went into Guardian mode 2500 rpms
We had more than that and it still had a over heat alarm and went into guardian mode 2,500 rpm’s
What should the water pressure be at idle & WOT?
I am having water pump/water pressure issues with my 1999 225 hp Opti serial $# OG913900.
last year I replaced the water pump and housing with a Mercury kit that I had purchased 2 years before....
I am hunting the part number for a 1999 225 Opti water pump kit. Serial # OG913900
my closest dealer said he thought it was the same as a Merc Cruiser but he wasn’t sure
I don’t want to tear it...
Having been a x-ray certified boiler welder whoever welded that couldn’t pass a welding test
Take a piece of shim stock or some material and open the tongue and put it the material in and close the tongue. Try to take any slop out and then pull it . If it still does it the problem is the...
I have a 99 Jag that was Gov. Mike Huckabee’s when he was in office. It has. 225 Opti with a 23 Tempest Plus. I have the build sheet and it came with the 23” prop. It jumps out of the hole and will...
I went thru Bearing Buddies like a fat kid thru candy. I finally just put regular wheel bearing caps on and have never thrown since
My 99 Jag belonged to Governor Mike Huckabee and I have the build sheet that came with it. It has a 225 Opti and came from the factory with a 23 Tempest Plus. The hole shot is great.
Ok thanks I will check the screw and if that has no problems I will call and get rebuild kits.
It will go all the way down until it is vertical.
OG913900
I have aq 99 225 Opti that the trim/tilt will leak down and let the motor go down. Is there a repair kit available?
I figure it Is a seal or o'ring leaking by.
Here is my take on the whole blistering deal. It doesn't make any difference which resin you have. Poor, good better or best, you have what you have. Don't get sick worrying about it If is that...
If the high pres. pump was frozen up I bet the low pres. is too. I have had to replace the low pres. pump twice in 4 years. Also the aftermarket pump is a Carter brand which was the original brand on...
The low and high pressure pumps were contract parts not made by Mercury. Get the part number off the original and put it in Google. I think I got mine from Jegs when I replaced it. I bet you had...
Well I guess I am SOL on finding a serial number but I did fix my problem. I removed the bottom aluminum plate on the foot pedal looking for the number and found a broken wire going to the...
I bought a used Maxxum 80 52" shaft and I am trying to find out the year it is. MK says the serial number is under the foot pedal on the side by the on/off button. There is nothing anywhere under the...
If I was doing a mini bolt I would parallel the original bolt instead of offsetting t. I think it will look much better. Looks stupid to me the way it is now.
Those are great comments about Ron and I am sure there were and have been many more since his passing. I want to give my condolences to the Pierce family.
I also want to say I have met Rick at 2...
I thought Loomis hadn't sold any blanks in several years. Are they back selling them?
I have a piece that is 20 inches by 16 inches by 5/8ths inch thick. Anybody have a idea on how to cut it up?
Wrong!!! If you have oil at the piston you will have oil in the air. Now I am not saying it will hurt your air brush because I don't know anything about them but
having worked on compressors for...