Search:

Type: Posts; User: Tx Champ

Page 1 of 20 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    15
    Views
    190

    You're welcome! :beers:

    You're welcome! :beers:
  2. Replies
    15
    Views
    157

    I've had 3 Champions over the last 30 years and...

    I've had 3 Champions over the last 30 years and none of them leaked.
  3. On its way!

    On its way!
  4. Replies
    15
    Views
    190

    No washer that I recall. Slip the clip on the...

    No washer that I recall. Slip the clip on the screwdriver so there is no interference with the hole or slot. If you're lucky you can get it on 1st try. I was able to get it started then pry it on...
  5. Custom Mold & Tint was the OEM supplier. You...

    Custom Mold & Tint was the OEM supplier. You might have better luck with them.
  6. Welcome Kit! Got an email address?

    Welcome Kit! Got an email address?
  7. Replies
    15
    Views
    190

    Champ 2001, I went out and looked and I have the...

    Champ 2001, I went out and looked and I have the 22" set. You'll have to heat the tip up with a torch before you can bend it and use a benchvise.

    546365 546366
  8. Replies
    15
    Views
    190

    Go to Harbor Freight and get the cheap set of...

    Go to Harbor Freight and get the cheap set of long screwdrivers and bend the flat blade over about 1/4". You'll also need a little LED flashlight and a buddy to hold the pedestal.

    I forget which...
  9. Replies
    15
    Views
    157

    Go back original. Nothing worse than lying your...

    Go back original. Nothing worse than lying your knee down on a big ass latch assembly, especially if it's a hot sunny day. Only modification I've seen is that some guys have done away with the...
  10. Replies
    10
    Views
    927

    TTT

    TTT
  11. As I think I mentioned before, I'm not familiar...

    As I think I mentioned before, I'm not familiar with the 3-way valve system. I can tell you that the pump switch in the Auto position is a fixed timer that is 1 minute on and 3 minutes off. In the...
  12. Replies
    15
    Views
    190

    Seen this? Replacing gas cly in snap lock...

    Seen this? Replacing gas cly in snap lock pedestals I've replaced 2 so far.
  13. Replies
    3
    Views
    89

    There's 1 listed Boats4Sale5...

    There's 1 listed Boats4Sale5 (bassboatcentral.com)
  14. Replies
    10
    Views
    398

    Paxlovid is for Covid. Hope you get to feeling...

    Paxlovid is for Covid. Hope you get to feeling better soon Rodney.
  15. Replies
    12
    Views
    317

    Congrats on the 198 ... you'll love it! Quagga...

    Congrats on the 198 ... you'll love it! Quagga mussels huh? That's a new one on me. Texas is dealing with Zebra Mussels.
  16. Replies
    2
    Views
    131

    6" Rapid Jack was the jack plate option from the...

    6" Rapid Jack was the jack plate option from the factory. It's the best mechanical plate there is. If they still offer the Champion cut, you want that.
  17. Thread: Hydrafoils

    by Tx Champ
    Replies
    6
    Views
    137

    My 210 isn't as fast to get on plane as my 201...

    My 210 isn't as fast to get on plane as my 201 was even with 50 more hp. My opinion is that the beam forward hulls, 198, 200, 206 & 210 have more hull in the water than the 86" and early 90" hulls. ...
  18. Replies
    7
    Views
    116

    Your 204 may be a little wider up there than the...

    Your 204 may be a little wider up there than the 201 accounting for the pedal location. The 204 was one of the first 90" hulls, the 201, 86".
  19. Replies
    3
    Views
    102

    Mark Talbert is who you want to talk to at C&O. ...

    Mark Talbert is who you want to talk to at C&O. Carol "The Parts Mom" has retired.
  20. Replies
    9
    Views
    186

    To All You New Guys...

    To All You New Guys
  21. Replies
    10
    Views
    927

    TTT

    TTT
  22. Thread: Hydrafoils

    by Tx Champ
    Replies
    6
    Views
    137

    They are not needed

    They are not needed
  23. From what I've read, Mercury 4 stroke likes less...

    From what I've read, Mercury 4 stroke likes less pitch than the comparable 2 stroke and the SHO can run the same prop.
  24. Replies
    11
    Views
    168

    :thumb up2: :thumb up2: :laugh:

    :thumb up2: :thumb up2: :laugh:
  25. Replies
    11
    Views
    168

    Well worth the money IMHO. Just need to use the...

    Well worth the money IMHO. Just need to use the recommended o-ring lube. I've never had an issue. And it's a whole lot easier on my knees ... :laugh:

    But back to your original question, yes the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4