Hey guys, I have a 2012 250 SHO with 700 hours, I keep it serviced per Yamaha dealer and have been well pleased. What is the average hour lifetime of these engines? Let me know how many of you have...
Type: Posts; User: rudebuck
Hey guys, I have a 2012 250 SHO with 700 hours, I keep it serviced per Yamaha dealer and have been well pleased. What is the average hour lifetime of these engines? Let me know how many of you have...
Hello,
I need some advice please. 2012 Ranger Z520 touch pad issue. The pad has been updated years ago, the pad will start the outboard. However, I cannot control any accessory, lights,...
It seems to be fuel related to me, I replaced the bulb last year and will go back and check all the fuel lines. Something like that will drive you crazy trying to diagnose. I also found out the...
Boat does not stay in the water any length of time. (Maybe overnight from time to time) Its garage kept and babied ! Could be electrical, it's almost like its in limp mode with no alarms trying to...
I have tried the jack plate in every position, and this boat use to jump out of the hole. How do you check for water logged stern? It almost acts like its a fuel issue, is it possible the fuel...
Hello,
Needing some advice, If I fill both live wells up on my Z520, two people in the boat, and 1/2 a tank fuel my boat will not come out of the hole without moving someone to the front deck. I...
This may seem like a crazy question, but I have been wondering since I have a 3 N 1 mounted on my Ultrex connected to my new HDS 12 Live is it possible to download the 360 software and manually move...
I cut the old transducer cable and used the pull string method, but no room for the bigger cable connector. Both my hydraulic steering cables run through the same conduit with the wiring. I only...
Getting ready to install new console electronics and trying to pull new transducer cable from rear to console. I cannot see any empty tubes, tube that is in use will not work as it is maxed out! ...
I will keep that in mind! Thanks
My 2012 250 SHO seems to be burning some oil during start up. Is this normal from time to time with trim levels? Oil level is within range all year, I have had compression test, leak down test,...
Hey guys tying to figure out my tilt trim problem and seeking some advice. Tilt trim starting acting up last fall, it would start off normal and slow down. I notice some oil around one of the seal...
I have a new 36 volt Ultrex which is under a year old. I noticed about half way through the summer last year when you put your foot on the pedal the motor would not turn. It was locked just like...
Thanks, Guess I can put it over the plug and try to get the boot over it.
Doesn’t appear to be, no other spark plug boot had this in it. It will go inside the boot, but not without effort. It also is very visible and no other boot had this in it that I could see.
It’s not, the other 5 did not have this attached.
Changing spark plugs on my 2011 VF250 I noticed #4 had this rubber grommet attached to the top of the plug. When I removed the coil it was on the plug. It was the only cylinder to have such a thing....
Spark plugs have less then 30 hours, main fuel filter on engine, and water separator have both been changed.
I have a 2011 SHO 250 on a Z520 with two Talons, Love the motor and boat combo ! This boat has always jumped out of the hole, but latley I have been experiencing some hole shot issues at times. If...
Hello folks,
I have a 2012 Z520 and I'm thinking about installing a Power Pole or Talon. We don't fish shallow water except in the spring, mostly highland reservoirs. Do you think its worth it?...
I read a post a few weeks ago about 89 Octane in the 250 SHO, I went to fill up for winter the other day and I always use NON Ethanol fuel. I can't find 89 octane in the non ethanol fuel any...
I bought a used 2012 520 with HDS system, I have two transducers mounted on the back hull with a console switch to activate. One is for down and side imaging, the other is for standard use. I...
The gauge reads 45 PSI it never moves no matter what the RPM's are. Power head was replaced last year, I think I may have a sensor not working or wiring harness loose. Dealer is a few miles away. ...
New to the SHO motor and I've noticed the water stream out the back is not very strong. Blows in the wind when running, weak at idle. I have Cleaned the hole, water pressure gauge is showing wide...
Intresting! Getting ready to take the 2014 225 for a break in this week. Dealer says go by the book? I guess you should break in the first 10 keeping an eye on the oil, change and run the %^&* out...