I can't find anything on this so, asking here. I have waypoints created and saved from my Gen 2 to SD card loaded to my new Gen3 touch that have about my first 17 waypoints connected with a black...
Type: Posts; User: Yanky Bob
I can't find anything on this so, asking here. I have waypoints created and saved from my Gen 2 to SD card loaded to my new Gen3 touch that have about my first 17 waypoints connected with a black...
Defined as jumping on pad, planning out, gunning it to run to next spot. Two local shops say no stator in my model EFI. Rates rpm at about 5600 and water press about 25 at wot. Currently at 5500...
One issue back to another? What is meant by "locking"? Also, why the hard reset after which upgrade?
It reads as version 18.2 and application 60.1.142.
Yes to all three of your questions.
Serial# 1B011758.
I've been having power loss issue at top end limiting rpm to about 5000 and now hard to jump on pad stalling if forced but, if I back off throttle and idle about a hundred...
Lowrance replaced my HDS 9 Gen2 filled with water with a Gen3 that I connected and set up a few days ago. Worked good in my driveway but, no sonar, temp, time or structure scan on water! Works at...
Lowrance is replacing my HDS9 GEN2 TOUCH with a Gen3 and need to know if I need to remove/replace any wiring or if I can just install head unit to bracket and go fishin' right away? Thank for any...
What are the newer maps called? Not the Hot Spots maps? Not sure yet where my fishing will be on the lake but, most likely will be spread out. I have been informed of the crazy traffic there!...
First time going to this Lake so, can anyone educate me on where I can (or can't) launch a bass boat at various places around the lake? Also, where on the water can I get gas if needed around the...
Thank you for the replies. What would be the recommended paint to use over the pc-7 that will not flake off? I'm assuming would have to paint the whole storage unit so it all blends together?
I can get 3M 5200 white locally and wondering if it is pretty much the same as PC-11 or PC-7? If I decide to use black carpet after epoxy what/where is correct carpet for a storage unit? Black...
Causes too much loose weight bouncing around in rough water.333224333225
My front storage compartment on my Triton TR196 starting to deteriorate. What is the best way to repair these cracks that are turning into holes? I have thought about just using two-part epoxy and...
This tank is 14 in deep. Had to use a Moeller Marine product 12" to 24" part number 35729 - 10 and bend it in a long "S" pattern going behind driver seat in order for it to fit and work top to...
Anyone know what legnth sender I need or depth of this tank Ft4422? I would prefer to have new replacement prior to pulling out the old one to avoid driving into/all over town or worst case having...
Ok, I figured how easy to post pics. Also, not sure if that screw top right on sender pic had a wire attached?
http://www.bbcboards.net/attachment.php?attachmentid=332407&stc=1http://www.bbcboards.net/attachment.php?attachmentid=332408&stc=1http://www.bbcboards.net/attachment.php?attachmentid=332409&stc=1http:...
Sending only has "8341-7015 5207". The fuel tank reads Moeller Marine Products model Ft4422. I found sending wire still connected with two green wires off ground. One green ran with red sending...
I'm looking to get my fuel gauge working again. Can anybody tell me what model number sending unit originally was in this '04 TR196PDC or perfect replacement for it? Years ago it was replaced from a...
The VST was cleaned out and high pressure fuel pump replaced and seemed to run good again this weekend. Very windy conditons and hard to find places to run wide open.
I got boat back after three weeks at the shop where they can't get it to act up or find anything wrong. They thought might be high pressure fuel reguator so, I let them change it and still have the...
So was your problem solved for this top end power loss? If so, what was it?
Serial #1B011758
Plagued like others with top end loss and maxing at 5000rpm when should be 5600. Short version is a lot of money replacing lines, filters, h2o pump, props, etc. Was running...
Thanks, PM returned.